计算程序

In order to find out how the branch structure affected the characteristic of shockwave propagation, LS-DYNA software was used to compute, and simulate certain shockwave propagating through the branch tunnels with different angle, and the overpressure/momentum bench mark to measure "plane wave" was proposed.

为了研究几何分叉结构对冲击波传播特性的影响，利用LS-DYNA三维数值模拟计算程序，对同一弱冲击波通过不同角度的两向分叉巷道时传播、衰减的情况行了数值模拟，并提出了超压／冲量准则来衡量&平面波&。

Based on the present method, the program computing dynamic response of bridge under moving train is developed.

根据本文提出的方法，编制了运行列车作用下桥梁动力反应的计算程序。

Analyzing the velocity fault map on the basis of XIGA, using the inversion measurement of dislocation model, I get the inversion answer by using MATLAB calculation program. The results show that: the velocity in strike slip of fault is larger than those in dip slip between spot WT12 in the south of Yalung Zanbo River and spot SHOT in the north of that. The conclusion that there is strike fault between the two spots is conformed.

研究分析以日喀则为参考的速率断面图，利用Okada矩形位错模型进行反演，结合MATLAB计算程序，反演结果显示在雅鲁藏布缝合带以南的WT12与雅鲁藏布缝合带以北SHOT两个测站断层中走滑速率明显大于倾滑速率，验证了两者存在走滑断层的结论。

For mechanical capability of busway, the magneto-structure coupling analysis is used and computation program is compiled by using apdl language of ANSYS in this paper, then the maximum dynamical force and displacement in X direction can be obtained under the condition of three phases short circuit to earth.

对低压母线槽的力学性能，本文运用了磁-结构耦合分析的方法，大量运用ANSYS的apdl语言，编制了计算程序，得出母线槽在三相对地短路情况下所受的最大电动力及X方向的最大位移，形成了磁-结构耦合分析模块。

A method to find the exact points of inlet and outlet of film-thickness of the EHL is introduced. A numerical solution of TEHL of the gear using Newton relaxation method and binary search method and the method to find the exact points of inlet and outlet is developed. By means of multiple regresion, a formula to calculate TEHL flash temprature of the gear is obtained.

推导给出了齿轮承载区内热弹流热流密度方程、无量纲参数团表示的热弹流方程和油膜入口点及出口点搜索确定方法，编制了由松弛因子牛顿法、对分法及油膜入口点和出口点搜索方法等组成的便于工程实际应用的齿轮承载区热弹流快速计算程序。

An analysis program of finite element for frame tunnel bridge is introduced.

论文中还编写了针对框架式地道桥的有限元分析计算程序。

Keywords modification coefficient;external gear shaper cutter;computing program;restricted conditions

变位系数；外啮合插齿刀；计算程序；约束条件

Morgan "A suit of computer programs for calculation refrigerant propeties" and make an improvement, gives the general programs of calculating thermody- namic properties suitable for thirteen Halocarbon refrigerantsR-

Morgan的文章&Asuit of computer programs for calculation refrigerant properties&进行了改进和完善，给出了适用于13种常用制冷工质(R-11，12，13，13B1，14，21，22， 23，113，114，500，502， C318)的通用计算程序。

Also, a numerical procedure for calculating the load responses of simply supported composite beams with concentrated force at the mid-span is established and verified with two samples.

推导了弹性工作状态下复合梁的界面滑移与应变的表达式，编制了数值计算程序并用2根复合梁进行了校核。

It is introduced how to measure and calculate the ferquency/wavenumber spectra.

并利用FORTRAN语言编制了振动时空信号的频率-波数谱计算程序。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。