计算的结果

Some typical torsion problems of a cylinder involving a straight,kinked or curvilinear crack were calculated.The obtained results for the case of straight crack...

对圆弧裂纹、曲折裂纹以及直线裂纹的典型问题进行了数值计算，并与用Gauss_Chebyshev求积法计算的直裂纹情形结果进行了比较，证明了方法的有效性和正确性。

When the data and ECC are read, the function is recomputed, the result is compared to the ECC appended to the data, and correction is performed if necessary.

当读取数据与ECC码时，再使用ECC码的计算函数进行计算，并将得到的结果与ECC码进行比较，如果可能的话更正发现的错误。

The possibility and extent of the goal reactions could be evaluated based on these calculations. The theoretical calculations also provided the basis for the choice of suitable catalysts and reaction conditions. The experimental results have demonstrated that the thermodynamic calculations are correct.

通过计算可判断所研究反应进行的可能性和程度，对催化剂和反应条件的选择提供了理论依据，实验结果也证明了热力学计算的正确性。

The results showed that if calculated according to the CaO standard deviation,the blending factor of raw meal homogenization silo was 1 only,far blow the design value(6~8);while calculated according to the KH sta...

结果表明，以CaO标准偏差计算的生料均化库的均化系数只有1左右，远低于6￣8的设计值；以KH标准偏差为统计指标计算的生料均化库均化系数为1￣1.5，窑系统均化系数为1￣2。

The robust and precise method consists of initial main direction extraction based on the direction histogram of structure tensor and precise direction detection on vectorized edge image.

该算法基于结构张量计算的方向直方图探测初始主方向，并根据矢量化的边缘计算精确的方向角，使得探测过程稳健、结果准确。

The transonic flutter characteristics are investigated for several wings, empennage and wing-body configuration, flutter critical speeds are numerically simulated.

以ONERA M6机翼和无后掠矩形机翼为算例，分别对它们的跨音速定常和非定常粘性绕流进行了数值模拟，计算结果和有关文献的结果进行了比较，吻合较好。

After applying them to a practical diesel engine, it is found that SIM2 is much better than FIM1 and FIM2 in prediction of the ring pack friction power loss and oil film thickness fluctuation in one stroke. In order to analyse the effects of the heat decomposition of the combustion products, a conventional cycle simulation program is designed. It can be used on IBM/PC.

为了便以分析产物热分解的影响，本文还专门编制了一套可在IBM/PC机上计算的以单区经验放热率模型为基础的低散热柴油机工作过程模拟程序，和多区模型相配合可方便地讨论燃烧产物热分解对计算结果的影响。

Based on discussion of attached plate and analysis of beam elements calculation results, a experience formula is deduced for the calculation of a beam element's inertial moment.

基于对梁元带板问题的讨论及对大量梁元的实际计算结果分析，推导出该梁元惯性矩计算的经验公式。

According to the analysis and computational results in this thesis, although the actual structure and work conditions of the pressure vessel in nuclear power station are much more complex than that of the pressure vessel model, the program FEARPV still can get quite good convergence on the plasticity andcontact iteration. And also the program FEARPV has good value stability, and good regularity. During the heating, compression, constant temperature, constant pressure, cooling and decompression process, the regularity is basically in common with that of the pressure vessel model.

由本文分析计算可知，虽然电站核压力容器的结构及计算工况较压力容器模拟体复杂得多，然而反应堆压力容器瞬态密封有限元分析程序对塑性迭代和接触迭代仍具有很好的收敛性，数值稳定性好，得到的结果具有良好的规律性，在升温、升压、恒温、恒压、降温和降压等过程中其规律和压力容器模拟体基本相似。

Within the limitation of SBTART model, the paper is concerned with the preliminary study of the feasibility of determining total atmospheric ozone by scattered ultraviolet radiation from the clear zenith blue sky.

选用SBDART模式作为大气辐射传输计算模式，通过模拟计算和结果分析探讨无云的晴天、垂直对天顶观测的紫外前向散射反演大气臭氧总量的可行性。

And discuss some key point of integrated management system design, include hazard identification and risk assessment and risk control in the occupational health and safety management, the measure of satisfaction target of customer, the flawlessness of law system, the integration of the integrated management system and enterprise standardization system, unify lead institution and work orgnization, integreted internal audit and integrated management review.

同时，论述了一体化管理体系构建中的几个主要问题，包括职业健康安全管理中的危险源辨识、风险评价和风险控制、顾客满意度的科学监测、法律、法规体系的完善、一体化管理体系与企业标准化体系的有机结合、统一的领导机构和工作机构、一体化的内部审核和管理评审。

Deepwater Taranaki is investigated for its petroleum potential, using all available seismic data tied to shallow-water wells.

运用与浅水井相关的现有全部震波探测数据考察了深海区塔拉纳基盆地的油藏前景。