计算的

The instructive conclusion was: 1 under the vertical loading, the shear-lag effect was produced badly, more severer under concentrated loading than under uniform loading .2 the longitudinal bending deformation of the beam flange was true of the imitating plane assumption of deformation . 3 the width length ratio was confirmed as the first factor working on the shear-lag effect among all the geometric parameters;4 the shear-lag coefficient of simple-supported box-girder was severer than the continuous box-girder, the shear-lag effect in the inner supported section of continuous beam was much more severer, we need paying more attention for it in designing. 5 the non-liner characteristics of material deformation have littlie influence on shear-lag effect in BGCW. 6 the experiential calculating formulation and calculating diagram for the effective flange width was raised with the only factor of the width-span ratio., but the primary location of axis of bending moments should not be changed while calculating the inertial moment .

研究认为：1室内模型试验和空间有限元分析结果均表明波形钢腹板组合箱梁在竖向荷载作用下，翼板出现了典型的纵向应力剪滞效应。2在竖向荷载作用下，截面高度上各点纵向正应变分布认为可符合"拟平截面假定"，以此作为波形钢腹板组合箱梁抗弯计算的基本假定。3箱梁宽跨比是影响波形钢腹板组合箱梁翼板剪滞效应的主要因素。4连续波形钢腹板组合箱梁的翼板剪滞系数大于简支梁，且连续箱梁内支点截面翼板剪滞效应相当严重，对此需十分重视。5当混凝土翼板受力由弹性阶段进入弹塑性阶段时，材料的非线性特性对翼板的剪滞效应影响甚微。6提出了根据组合箱梁的宽跨比参数来计算翼板有效宽度比的经验公式和计算图表，但箱梁截面抗弯惯性矩的计算不应改变原先的截面中和轴位置。

Then the boundary element integral equation of interior and exterior form is deduced in detail, also the form with corner coefficient. The significance for numerical calculation and principle of the singular integral is analyzed, and a non-isoparametric transformation method is presented to calculate weak singular integral and Cauchy integral, the method presented provides us a very simple way to computer the two kinds of singular integral of Helmholtz boundary integral equation, and it is easy to program in computer. After the difficulty of the calculation for multi-frequency of Helmholtz boundary element is explained, a method named SECHIEF (Series Expansion Combined Helmholtz Integral Equation Formulation), which is focused on the computational efficiency, is presented.

对结构声辐射的边界积分方程的内部形式与外部形式进行了详细的推导，给出了角点系数的计算方法与边界积分方程的形式，在此基础上，分析了奇异积分产生的原理及其对数值计算的重要性，提出了一种计算奇异积分的非等参(来源：Ae8a8BC论文网www.abclunwen.com)单元的变换方法，该方法给Helmholtz 声学边界积分方程中的弱奇异积分与Cauchy 奇异积分的计算以及编程提供了极大便利。

The main contributions of this dissertation are In chapter 2, we propose a scientific visualization system modal which is based on large-format display technology and Client-Commware-Server structure. In chapter 3 and chapter 4, we accomplish two large-scale scientific visualization systems. In chapter 5 and chapter 6, we propose HFFT on hexagon and parallel dodecahedron domains, and reduce the computational complexity from O and O to O and O . Lastly, we propose a parallel HFFT on distributed memory computers.

本文的主要贡献如下：提出了使用大屏幕显示技术、适用于大规模科学计算可视化系统的Client-Commware-Server模型；实现了油藏数值模拟和分子模拟两个大规模科学计算的可视化系统；给出了二维三方向六边形区域、三维四方向十二面体区域上的HFFT算法，将变换的计算复杂度分别从直接计算的O和O量级降到了快速算法的O和O量级；最后，本文给出了一种基于分布式存储的并行HFFT算法，并对影响、提高并行算法的若干因素进行了分析。

In the third part, the theory of thrust angle and unbalanced forces is studied andapplied to Xiluodu arch dam. some conclusions are obtained :(1) The thrust angle issmaller by elaso-plastic computation than elastic computation. For the non-linearcomputation, the thrust angles at different elevations all increase during overloading,which reveals the internal mechanism of good performance of arch dam in conditionof overloading;(2) The elaso-plastic theory always minimizes the actual unbalancedforces in the sense of a condition number in the norm ofcomplementary energy.

第三部分，通过对溪洛渡拱坝拱端推力角及不平衡力的研究，得出如下结论：(1)非线性计算较弹性计算的推力角大；对于非线性计算而言，拱坝超载过程中各高程段的推力角均有所增加，这反映了拱坝具有较高超载能力的内在机制；(2)在总余能范数的意义上，按弹塑性本构关系确定的不平衡力或加固力是最小的，弹塑性计算确定的加固力和真解相比偏于安全。

The inner force of the line element for underground structure have been calculated using the traditional finite element mesh and high-order manifold method to guarantee the numerical precision of the line element and overcome the disadvantages due to the geometry error between the actual position and computational position of the beam and truss element in common use.

用传统的有限元网格和流形方法的高阶覆盖位移函数来进行地下结构的杆、梁单元计算，保证了线单元模拟的数值精度，同时又克服了常用的杆、梁线单元计算位置与实际位置不相符合从而带来计算误差和结构设计不便等缺点，提供了一种解决结构数值计算的较好的途径。

Excel software can be used to realize the automation of interpolation calculation,that is,preparing a calculation table of tank capacity with Excel software,storing the value of tank capacity into the calculation table,thus the corresponding volume data can be obtained only after inputting the data of liquid level,with prompt and accurate .

使用Excel软件可以实现内插计算的自动化，即用Excel软件制作一个罐容计算表，并将罐容表值存入计算表中，只要输入油高即可得出对应的容积值，迅速而准确。

The main works are listed as follows:1 Thermal Computi ng model of steam pipe network were built with good match to actual operating dataThe thermal calculation model of steam pipe network was established according to the steam pipe network heat transfer characteristics and the thermal equilibrium principle,. It includes steam temperature drop expression, the expression of per unit length heat loss when steam pipe laying in different ways and total heat transfer coefficient expression.

该模型由管内蒸汽温降方程、不同敷设方式蒸汽管道的单位长度散热损失方程、总传热系数方程等组成，利用散热损失计算公式对钢套钢蒸汽保温管道不同敷设方式、不同管径的散热损失等总传热系数的影响因素进行了分析，计算结果表明三方程联合求解提高了新建蒸汽管网热力计算的准确度，可用于新建蒸汽管网的热力计算。

The present thesis construct the boundary model on carburettors which is based on themethod of characteristics. The IEM computer program for computing the wave action and ex-change gas process of the gas oline engine is accomplished by using the method of characteristics.

建立用特征线计算的代油器边界模型，利用非等墒特征线理论编制了可计算汽油机进气管内的压力波动及换气过程的计算机程序IEM，并用该程序对BJ492QA汽油机进行了计算，计算与实测的压力波曲线吻合良好，表明了该化油器边界模型及IEM的合理性。

The results of our numerical simulation show that the numerical method applied in our paper is practical, the calculation results match the actual situation properly; the digital images from numerical simulation possess a positive significance in understanding and improving the heat flow distribution of the meat dry kiln. The proposed method provides a feasible approach to analyze and improve the flow field of meat dry kiln with numerical simulation.

数值计算的结果表明：本文所用的数值计算方法是可行的，基本符合实际情况；所得计算结果分析图像对了解干燥窑中流场的分布情况和如何改善干燥窑流场分布具有积极的参考意义，本文所提出的方法为采用数值计算方法分析改善干燥窑流场问题提供了一种可行的手段。

Compared with traditional method by solving a Jacobi matrix, calculating account is greatly decreased because only displacement and center of buoyancy need computing while those elements of waterline plane are not required.d Based on the research mentioned above, the paper presents the computer programmes of compartment definition, free surface effection, and some modules of the programme of the intact and damaged stability calculation.

与传统的拉格朗日乘子法相比，该优化方法公式推导简单，而且每次迭代只需计算水线面以下的排水体积和浮心坐标，不需计算水线面上的面积、漂心、惯性矩等要素，计算方法直接简便。 4在以上理论研究的基础上，开发了舱室定义，自由液面修正的计算机软件；编制了船舶完整、破损状态下的浮态、稳性计算的部分模块。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。