计算的

Through analyses and comparisons with other methods, the equation squared root method of current is applied for the distribution line loss. Aim at the shortcomings of traditional equation squared rood method of current, improved methods are presented. This papers presents the treatment of small power sources in distribution network and the loss calculation of transformer winding resistance. In addition, the method on the base of queue is applied for programs.

通过对当前较为成熟的几种配电网线损计算方法的深入研究，分析和比较了这些方法的不同特点，并针对传统均方根电流法的不足，提出了对配电变压器铜损的改进计算方法；提出利用等效容量的概念来解决小电源问题，使得在配电网理论线损计算中对小电源的处理变得简便易行；在配电网理论线损计算的程序实现上，引入了基于队列的设计方法，不仅极大地提高了计算效率，而且可以得到任意节点的线损数据，方便了线损计算和管理。

For the ill conditioned load flow caused by the error produced in the transformation from electricity quantities to average power, direct current load flow and sensitivity vector are presented to find out the ill node, then by adjusting the load curve and generation curve in a certain principle, which is shown in detail with several flow charts, a new operation mode is reestablished to ensure the convergence of the calculation. Optimal multiplier method is proposed to work out the least square solution according to ill conditioned structural power network. The electricity quantities flow method enhances the reliability and accuracy of the calculation of the power transmission losses.

该方法可根据当前输电网中各个变电站24小时的电量记录，利用电量潮流计算对输电网总线损和各条线路损耗进行计算，使计算的精度满足降损措施分析和指标考核的要求；并且对于由负荷出力曲线转化成平均功率计算潮流时引入的误差，进而导致潮流计算不收敛的情况，采用直流潮流法，依据相角对有功功率的灵敏度向量判断出"网络异常点"，并且给出了解决此种情况的方法流程图；针对结构病态的电力系统潮流计算不收敛的情况，运用非线性约束优化方法中的最优乘子法求解潮流方程的最小二乘解，从而解决了电量潮流法计算理论线损时的收敛性问题，增强了该方法的适用性。

Some new method is presented in this paper: A. An Integrated parameters computation method to analysis asynchronous operation of the turbine generator is given, including the equivalence of short circuit and open circuit of field windings, deducing boundary condition of 〓 method and computing frequency parameters. B. A new memory structure for sparse complex matrix and a PCCG method based on it are introduced to save memory and computation time. C. An equivalent method of vacuum is presented, and effectively eliminate the effect of corner point and accelerate convergence of PCCG method. D. Coupling the computation of electromagnetic and temperature field is discussed and model for computing temperature field of the turbine generator rotor at asynchronous operation is built.

文中提出了以下新方法：(1)在失磁异步运行转子三维涡流场计算中提出了完整的参数计算方法，其中包括励磁绕组开、短路的等效，〓法边界条件的推导及频率参数的计算方法；(2)提出了铁心内空气域的等效方法，有效地解决了开槽引起的角点奇异问题，并提高了方程组的迭代收敛速度；(3)在〓法有限元模型中，创立了一种能节约内存、提高计算速度的压缩存储矩阵格式，并建立了基于该格式的方程组解法；(4)提出了涡流电磁场和温度场两种不同场计算的合理结合方法，建立了转子三维稳态和时变温度场的有限元计算模型。

This article trend research and current situation of computing technology analyze in survey, through to simple network familiarity that trend calculate, take circuit of simple equivalence as an example, carry on circuit voltage and calculation that power loss of the first part and the concluding paragraph mainly, and then regard a ring network circuit as the main example and carry on the detailed trend to calculate, calculate all nodal voltage power losses, use ATP software to carry on artificial calculation with this example again, it's a pity ATP software emulation has not succeeded.

该文在综述了潮流计算方法的研究和现状分析，通过对简单网络潮流计算的熟悉，主要以简单型等值电路为例进行电路首尾的电压和功率损耗的计算，再以一环网电路为主要例题进行详细的潮流计算，计算各节点的电压功率损耗，再以此例题用ATP软件进行仿真计算，可惜ATP软件仿真没成功。

Some kinds of culculation methods of elastic deformation of point contact surface are compared.

二。通过编程计算，比较和总结了点接触EHL弹性变形计算的几种计算方法，首次提出了在各层网格上分别采用不同的弹性变形计算方法的思想，以保证在多重网格法求解中变形转换的精度一致，计算时间最少。

Using principia of stiffness equivalent, it could be transformed to the bracing system so that the soft ware can calculate. Then calculate the member individually, including the calculation of load-behavior capacity, the calculation of high strong bolt with the method of connection with beam, the design method of stiffening rib, etc. The text educed the above-mentioned formula theoretically.5. Linking with windmill flat engineering example in the third youth flat engineering of Yi Zhuang Development Area, Beijing, It and steel frame constitute the steel frame? steel shear wall with slit system respectively are analyzed the whole structure by ANSYS and SATWE. The result is consilient.

既利用刚度等效的原则，把其转换为工程计算软件可以计算的支撑体系，然后对构件进行单独计算，包括承载力的计算、和梁接合方法——高强螺栓的计算、加强肋的设计方法等内容； 5、带缝钢板剪力墙与钢框架形成钢框架——带缝钢板剪力墙结构体系，结合北京亦庄经济开发区青年公寓三期工程中的风车公寓工程实例，分别采用ANSYS和SATWE进行了结构整体分析，两者的计算结果相吻合。

In this method the initial values of perspective projective matrix; rotative matrix and translative matrix are calculated from the fundamental matrix, than these matrices are optimized based on the coordinate value of corresponding points.

该方法从基本矩阵计算初始透视投影、旋转和竖直平移变换矩阵，然后以对应点坐标为基础对这些变换矩阵进行优化计算，从而有效地避免了优化计算的局部最小值，而且不过分依赖基本矩阵的计算精度。

All of these formalisms were shown to be equivalent in computational power -- that is, any computation that can be performed with one can be performed with any of the others.

所有的这些形式方法都与计算的能力等价，也即，一个计算可以和另一个计算能够被执行，那么这个计算也能够实现其它任何计算的执行。

Design on the principle that security , economy are rational , esthetic , fix up the selection of structure and structural level of every floor, assign , turn into with PK software AutoCAD revise the part behind the structural level well; Adopt stair and floor calculating and designing a teacher to appoint by hand, and calculate the appointed floor with PKPM software, compare with the floor that calculates by hand, fetch the drawing construction drawing of the head of the two; Calculate by hand the frame which the teacher appoints loads, set up good PKPM and calculate the procedure model of the frame , calculate frame internal force and output file result with PKPM , calculate , get PKPM structure mix muscle picture turn into AutoCAD carry on part punish; Build up pieces of internal force association from frame that PKPM obtain , choose three group unfavorable association design the materials as the foundation most, carry on the design basis of the craft, and draw and obtain the basic detail drawing and match the muscle with AutoCAD.

建筑毕业设计计算书74页、CAD图纸、施工组织设计全套摘要：本毕业设计以指导老师发放的《港市公安局巡警支队办公楼》建筑施工图纸为原始资料，进行结构设计和施工组织设计，设计的主要依据为现行的建筑行业规范以及指导老师的指导思想。设计以安全、经济合理、美观为原则，进行结构选型和各楼层结构平面布置，用PK 软件布置好结构平面后再转到AutoCAD上进行局部修改；采用手工计算设计老师指定的楼梯和楼板，并用PKPM 软件计算指定楼板，与手工计算的楼板进行比较，取二者之长绘制成施工图；手工计算老师指定的框架荷载，建立好PKPM计算框架程序模型，用PKPM计算框架内力并输出文件结果，把PKPM计算得到结构配筋图转到AutoCAD进行局部处理；从PKPM得出的框架构件内力组合，选择三组最不利的组合作为基础设计资料，进行手工设计基础，并用AutoCAD绘制得出基础详图及配筋。

Design on the principle that security , economy are rational , esthetic , fix up the selection of structure and structural level of every floor, assign , turn into with PK software AutoCAD revise the part behind the structural level well; Adopt stair and floor calculating and designing a teacher to appoint by hand, and calculate the appointed floor with PKPM software, compare with the floor that calculates by hand, fetch the drawing construction drawing of the head of the two; Calculate by hand the frame which the teacher appoints loads, set up good PKPM and calculate the procedure model of the frame , calculate frame internal force and output file result with PKPM , calculate , get PKPM structure mix muscle picture turn into AutoCAD carry on part punish; Build up pieces of internal force association from frame that PKPM obtain , choose three group unfavorable association design the materials as the foundation most, carry on the design basis of the craft, and draw and obtain the basic detail drawing and match the muscle with AutoCAD.

土木工程毕业设计 6层办公楼计算书+图纸+施工设计全套）摘要：本毕业设计以指导老师发放的《港市公安局巡警支队办公楼》建筑施工图纸为原始资料，进行结构设计和施工组织设计，设计的主要依据为现行的建筑行业规范以及指导老师的指导思想。设计以安全、经济合理、美观为原则，进行结构选型和各楼层结构平面布置，用PK 软件布置好结构平面后再转到AutoCAD上进行局部修改；采用手工计算设计老师指定的楼梯和楼板，并用PKPM 软件计算指定楼板，与手工计算的楼板进行比较，取二者之长绘制成施工图；手工计算老师指定的框架荷载，建立好PKPM计算框架程序模型，用PKPM计算框架内力并输出文件结果，把PKPM计算得到结构配筋图转到AutoCAD进行局部处理；从PKPM得出的框架构件内力组合，选择三组最不利的组合作为基础设计资料，进行手工设计基础，并用AutoCAD绘制得出基础详图及配筋。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。