触发电压

The single edge-triggered flip-flop uses low swing voltage delay chain generating the operation transparency window for reduces the power consumption.

此单缘触发正反器使用了低电压的时脉震荡延迟电路，来产生操作的触发波形和电晶体叠加技术，来达到减低漏电流的低功耗设计。

By means of forced synchronization of current in thyristor branch with the line current, the mode switching from capacitive mode to Bypass can be implemented. In the switching strategy from capacitive mode to inductive veriner mode, a method of thyristor conditional firing is put forward. The thyristors will be fired and conducted on condition that both line current and capacitor voltage are inphase.

通过强制晶闸管支路电流与线路电流同步，实现由容性区到Bypass模式的切换；在由容性区到感性微调模式切换的过程中提出了晶闸管条件触发的方法，即当线路电流和电容电压满足同向条件时晶闸管才触发导通。

In the proposed device to remedy the defect that overhigh withstand voltage of thyristors used in converter are needed due to the overhigh DC link voltage, a method to control DC link voltage is put forward, that is, a special control logic for full-controllable switching elements is designed to make them equivalent to half-controllable switching elements which are naturally turned on and turned off by triggering, then connecting such a half-controllable switching element in series with DC link the defect of overhigh DC link voltage is effectively solved.

为了克服该装置直流母线电压过高，因而对逆变器开关管耐压要求过高的缺点，提出一种对直流母线电压进行控制的方法。对全控型开关器件设计一种特殊的控制逻辑，使其等效为一个自然导通、触发关断的半控型开关器件，将该半控型开关串联在直流母线上，有效解决了直流母线电压过高的问题。

Two dimensional fluid simulation results show that the wall voltage across the sustaining gap is increased by 30V, and the sustaining voltage can be lowered by 10-20V with the new triggering method. The vacuum ultra-violet radiation efficiency is increased by more than 50% compared to the conventional three-electrode AC PDP.

二维流体模拟结果表明，新的触发驱动方法可将五电极AC PDP主维持间隙的壁电压提高30V左右，从而使其维持电压降低了 10~20V，降低了对驱动电路的要求，同时真空紫外辐射效率比传统三电极AC PDP提高了50%以上。

The dimmer control circuit comprises: three-end bidirectional controllable silicon switch element, comprising grid and turned on by trigger signal of the grid, connecting to AC power supply through lamp load; and a first variable resistor, possessing adjustable resistance and regulating lamp brightness by following modes: changing resistance value of the first variable resistor, changing phase of the trigger signal corresponding to AC voltage waveform, prolonging or shortening turning-on time bucket of three-end bidirectional controllable silicon switch element, thereby changing current provided to the lamp load.

一种调光器及调光控制电路，该调光控制电路包括：三端双向可控硅开关元件，其通过灯负载连接到交流电源，其中，三端双向可控硅开关元件具有栅极，并且由输入到所述栅极的触发信号开启；以及第一可变电阻器，其具有可调节的电阻值，其中，通过以下方式来调节灯负载的亮度：改变第一可变电阻器的电阻值，改变所述触发信号相对于交流电压波形的相位，延长或缩短所述三端双向可控硅开关元件的开启时间段，从而改变了提供给所述灯负载的电流。

Record data include generator voltage UG1,UG2, auto setting value UGREF,manual setting value IFREF, trigger angle ARF, active power P, reactive power Q, rotor voltage Ufd, field current Ifd, generator frequency F0, local cabinet output current ILA, other cabinet output current ILB.

记录的数据包括发电机电压UG1，UG2，自动给定值UGREF，手动给定值IFREF，触发角 ARF，有功功率P，无功功率Q，转子电压Ufd，励磁电流 Ifd，发电机频率F0，本柜输出电流ILA，它柜输出电流ILB。

The input of the equipment can have 0-100% ungraduated continuous control.

设计先进的SCR可控硅调压控制系统，采用高精度的数字触发装置，准确的发出每一个SCR控制脉冲，设备的输入功率能作0～100%的无级连续控制，并有电压自动反馈系统和电流保护系统，保证主回路电压波动≤±1%。

After the research it is held that when internal fault takes place in the transmission line where the series compensation device is located, the corresponding protective measures, e.g., the forced triggering the by-pass gap, etc., is the effective approach to avoid the appearance of excessing level of transient recovery voltageand oversize coupling current.

文章结合我国南方电网河池固定串补及平果可控串补工程，对超高压输电线路装设串联电容补偿装置后的系统状况进行了比较深入的研究，指出一些系统问题，如过电压水平升高、潜供电流增大和可能发生的次同步谐振均源于串联电容补偿装置的固有特性，通过研究认为当串补所在输电线路发生内部故障时，采取强制触发旁路间隙等保护措施，是避免出现系统恢复电压水平超标和潜供电流增大等问题的有效途径。

Secondly, the operating principle and the mathematical model and the control method about the three-level voltage source high power factor PWM converter are analysed .The generation of the PWM trigging pulse control signal are introduced emphatically. On the basis of this, the hardware experimentation circuits are built with DSP and CPLD, and the trigging pulse signal is generated exactly. The feasibility of the circuit is verified by the experiment result.

其次，分析了三相电压型变流器的原理、模型、控制方法并着重研究其PWM 触发脉冲控制信号发生技术，并以DSP、CPLD 等芯片搭接了硬件试验电路，产生了正确地触发脉冲信号，试验结果证明了设计的合理性。

In order to solve this problem, a control strategy is developed. A control algorithm to suppress negative sequence current through ASVG caused by slight asymmetry of system is also developed based on the modeling method in function of switchings and the definition of instantaneous negative sequence voltage. The ASVG can generate a negative sequence voltage component against that in the system while it generating positive sequence voltage with this algorithm.

在系统轻度不对称时，本文提出了通过控制ASVG触发脉冲使其产生与系统电压负序分量大小和相角完全相同的负序电压以抵消系统电压负序分量，从而抑制ASVG负序电流的方法，并用&开关函数&建模法给出了具体的控制算法。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。