解析法

To the late 50s entered the computer photogrammetry, photogrammetry research areas has been greatly extended: If the analytical method aerial triangulation, on-line aerial triangulation, local area network adjustment, gross error detection theory, orthographic correction

到50年代末计算机开始进入摄影测量，摄影测量的研究领域得到了很大的扩展：如解析法空中三角测量、在线空中三角测量、区域网平差、粗差检测理论、正射纠正

It show that interstitial fluid pressure changes its sig n twice within one arteriolar vasomotion period and it is therefor not important that interstitial fluid pressure is a little higher or lower than atmospheric p ressure; arteriolar vasomotion can periodically result in lymph formation and in terstitial total pressure plays an important role in this procedure; local regu l ation of microcirculation can meet metabolic need to some extent in the form of dynamic equilibrium.

利用解析法与有限元法相结合的&影响线算法&，求解了第一部分中建立的数学模型，分析了微循环系统动力学的若干重要问题，表明在微动脉自律运动周期内，间质流体压力将两次改变符号，因而某些理论中十分强调的间质流体压力是略高于或略低于大气压力的问题显得并不重要；微动脉自律运动能导致周期性的淋巴形成，间质总应力在这一过程中起着重要作用；微循环局部调节可以以动态平衡的方式在一定范围内满足代谢的需要。

This made it possible for the forward problems in inverse problems to be solved by analytical method instead of numerical method. The new equivalent source method is over ten times rapider than the volumetric integral equation method.

这一方法使得电磁场正问题的求解由一般的数值方法计算改进为用解析法求解，使缺陷的重构速度比用体积分方程法提高十倍以上。

A rigid-plastic FEM program for the analysis of working piece deformation in single pass hot bar rolling was developed. Combining with the analytical model, the strain and strain rate of hot rolled bearing steel GCr15 bar during roughing and intermediate rolling processes was calculated and compared with the real values.

应用刚塑性有限元法开发了轧制过程单道次变形分析的通用程序，与解析法结合对实际热连轧生产GCr15棒材的粗轧和中轧过程中的应变－应变速率进行了计算值与实际应变的对比。

The computed results showed that the section shape of rolled piece and the crown of strip calculated using the analytical method and the finite element model are similar to that of the field measurement, which effectively verifies the proposed research methods and the formulated model.

计算结果表明：采用解析法、有限元法计算出的轧件断面形状与现场实测出的轧件断面形状及板带凸度数值相近，这说明研究方法和模型的有效性。

In the third chapter, using the methods of nonlinear feedback functions and Lyapunov functions and combining analytical with numerical methods, the nonlinear feedback methods are introduced and the synchronizations of chaos in Hadley system of aerographs and LFRBM system of physics are realized. Some of nonlinear feedback functions are constructed.

第三章在介绍非线性反馈方法原理的基础上，应用非线性控制的基本思想及Lyapunov函数方法，将解析法与数值法相结合，分别对气象学中著名的Hadley环流和物理学中的LFRBM系统进行研究，找到了一类非线性反馈函数，实现了混沌自同步，并利用Mathematica软件进行仿真实验，数值结果说明了该方法的有效性。

This paper deals mainly with the stray current distribution in running tunnel of metro by means of analytical method of equivalent circuit diagram and the analytical method ,and discusses the influence of resistance of rail to ground and the resistance of track on the variation of stray current.

利用等效电路分析法和解析法分析了地铁区间隧道中杂散电流的分布，探讨了轨地过渡电阻值以及走行轨阻抗对杂散电流变化的影响，得出轨地过渡电阻的降低和走行轨阻抗的增大是区间隧道中产生杂散电流的主要原域。

six-bar mechanism ; kinetic characteristics ; analytic method ; motion simulation

传统的平面连杆机构运动分析方法有图解法、实验法和解析法。

As to the short-span suspension bridge in little span, the numerical analysis method may be used for construction control calculation simply, and precision of calculation by numerical analysis method correspond to it by the finite element theory, meeting the demand of the construction control.

对于小跨径悬索桥，可以将计算简便的解析法用于悬索桥施工控制计算，而计算结果精度与有限位移法求出的结果相当，满足施工控制要求。

On the basis of hypothesis and experiment on the single rice miller,by graphical construction or analytical method,the rice milling craft characteristic chart can be mapped out,then,broken rice rates of different kind of rough rice,and under different milling crafts and op.

为了降低碾米的碎米率，应当根据稻谷原料性质及碎米率的预测，合理制定碾米工艺和调整操作基于假设和通过单机碾米试验，可用作图法或解析法绘制碾米工艺特性图，据此可以预测各种稻谷原料在不同碾米工艺和操作条件下的碎米率。

The reasons of iron ions content overproof in grade Ⅱ desalting water system,such as variation water quality,contamination of regenerant , operation adjustment of pretreatment system and switching operation of bed were discussed.

对二级脱盐水系统中铁离子含量超标的原因，如来水水质发生波动、再生剂受到污染、预处理系统操作调整、床体运行切换等进行了论述。

You were hired to drum up new business, so go and do it.

公司雇你招徕新业务，你就做你的事好了。