角系数

The method of setting up an affine coordinates system to solve the problems for the spatial crank and rocker mechanism is proposed.

分析并回顾了在给定摇杆两个极限位置及行程速度变化系数的情况下，最小传动角为最大的平面曲柄摇杆机构和空间曲柄摇杆机构的设计问题。

Based on this relationship, the v of the amphibolite obtained is 6.390 7 km/s, and the pressure coefficient is 0.160 6 km/.

依据该线性关系，得到常温常压下斜长角闪岩的弹性波纵波速度为6.390 7 km/s，压力系数为0.160 6 km/。

Use angle encoder calibration coefficient of deviation of the long focal length of high-precision tracking system was satisfactory results.

利用编码器标定角偏差系数的方法，在长焦距高精度跟踪系统中获得了满意的效果。

Aim To study the effects of walk-off angle on the coefficients of reflection and transmission.

目的 研究离散角对反射与透射系数的影响。

The authors calculated the energy deposition coefficients of 4He + on C and Cu under the normally incident condition by using the improving bipartition model which accounts for the angular correlation of energy losses partly.

利用部分地考虑了能量损失的角关联的改进离子输运双群模型，计算了4He＋离子垂直入射到C和Cu上的能量沉积系数，改进了早期的离子输运双群模

For non-Kolmogorov turbulence, the anisoplanatiam error, the angular correlation function of Zernike polynomials, the residual phase structure function and the long-exposure OTF after low-order modes correction are analyzed.

分析了非科尔莫戈罗夫湍流情况下，自适应光学系统低阶模式校正时的非等晕误差、泽尼克系数角相关函数、残余相位结构函数以及长曝光光学传递函数，并定义了一个新变量模式校正因子，用来有效评价目标非等晕误差对低阶模式校正自适应光学系统补偿效果的影响。

In the thesis, it was shown that the latitude variation of the angular dispersion should mainly depend on square sum of lower degree deduced Gaussian coefficients if the non-axial-dipole component vs. the axial-dipole component is small.

本文证明，如果地磁场非轴向偶极子分量相对轴向偶极子分量为小量，那么VGP角散布的纬度变化主要由低阶约化Gauss系数的平方和决定。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

Considering the problems of spurgear precise plastic forming, such as high deformation resistance, poor flowability and especial hardness to fill cant of gear, technological plan was developed based on precise plastic forming technique, successive control principle and consecutive local deformation theory. Moreover, structures of the rolling preform die and the die with up and down wellrounded forcer for stamping-extrusion and bulge-extrusion combining forming were designed too.

因此本文的主要研究内容和结果如下：本文以某种直齿轮：模数m＝2，齿数z＝20，压力角α＝200，变位系数x＝0为对象，针对直齿轮精密塑性成形变形抗力大，流动性差，特别是成形中齿轮角隅部分更加难以充满问题，基于精密塑性成形技术、逐次控制原理以及连续局部变形原理提出了&直齿轮滚轧制坯－镦挤、胀挤复合精成形&的工艺方案，设计了滚轧制坯的模具结构和上下冲头带圆角的镦挤、胀挤复合精成形的模具结构。

On the basis of the modeling and analyzing of the transmission system of the PQS-3-D elevator for car in the preamble, this article analysis the reason of the small difference of the angular speed, angular acceleration, angular displacement curve between the bilateral symmetry components. Actually, it is the result of that the torsional rigidity of the bilateral drive shafts are different, therefore has made the revision suggestion to the drive shaft parameter.

在对PQS-3-D型汽车专用升降机传动系统建模分析的基础上，分析左右对称传动构件的角速度、角加速度、角位移曲线在系统起动时间内有较小差异的主要原因，发现是由于左右传动轴的扭转刚度系数不同造成的，故对传动轴的参数做了修改建议。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。