角板

The company is committed to theGreen Environmental Protection Career in the world: production and machining of honeycomb paper pallet, cartons, paper angle bead, honeycomb paper gasket, cardboard and paper core.

公司致力于世界绿色环保事业---蜂窝纸卡板、纸箱、纸护角、纸衬垫、以及纸板、纸芯的生产加工。

EXPANDED METAL,PERFORATED METAL,HIGH RIBBED FORMWORK,RIBBED LATH,STEEL METAL PLASTER ANGLE BEAD,STEEL LINTELS,FIRE PROTECTION PLASTERING EXPANDED META...

扩张网，冲孔网，不袗网，免拆模板，金属角条，楣梁，菱形网，围篱网，龟甲网，格子板，浪型网，止滑板，。。。

Use the technology advantage of light -conducting panel to make the light beam and angle reach the best effects.

利用导光板的技术优势，使光束与射角均达到极佳状态。

Both ends of each bearing bar shall be attached to the carrier plates with a 1/8 inch (3 mm) continuous fillet weld on one side of the bar.

在支撑梁的一个边上，用1/8英寸（3毫米）填角焊将支撑梁连到载板上。

At the same time, cement concrete pavement of the disease also followed up wanton growth, the most common was undoubtedly the most easy to produce gnawing edge off angle, wrong units, broken plates, such as mud jack.

与此同时，水泥混凝土路面的病害也跟着肆意增长起来，最为常见的最易产生的当属啃边、掉角、错台、断板、唧泥等。

Special localized cutting communication with the customer; 2.5 If not available notched hole diameter less than 60 mm hole, can be used to be relatively enlarger for the opening; After opening 2.6 backplane approach, starting with the opening negative, positive exposed bit sharp, nated from the positive control (both sides maintain collapse teeth); 3 connected corner of the corner of the 3.1 connection method, identify three Kok code on the middle and lower (50 mm poured from top to bottom. Another try a) 3:00 even in the corner of the counter and cross wooden cabinet on the sideboard; 3.2 corner of the Outer Limits with a shutter-ping; 3.3 In accordance with the drawings corner of the size, will have a fixed angle of the black reinforce the lower corner with 3:00 counters even

特殊局部地方的切割必须与客户沟通； 2.5如割口不大可用圆孔、直径小于60mm孔，可用相对应的扩孔器进行开孔； 2.6后背板开孔方法，先从反面开孔，正面露出钻头尖时，再从正面往里操作； 3 转角条的连接 3.1转角条的连接方法是，找出三个角码，上中下（上下50毫米往里，另居中一个）三点连在与转角柜交叉柜体的侧板上； 3.2转角条的外沿与门板一平； 3.3按照图纸转角条尺寸，将已固定的转角条用黑钉上中下三点与转角柜连

My main production plant: Diamond Drawing Die, die of natural Drawing, polycrystalline Drawing Die (square, flat line, 2.60, etc.), cd Drawing Die, Die Carbide, drawing die, spiral die, die stamping, Nail Die, Roll plate, powder-coated, straight-mode (the standard-subscript)-reduction mode, a line-and gas-wire for mold (500 kilograms, not the general bias), welding electrodes Die (wire feeding flywheel , Ramps round, the former silk eyes, pipe knives, straight-tile block, powder-coated, etc.), wire and cable die, die square, flat-Die, Die, such as 2.60 and high-tech drawing powder, recycling all kinds of Carbide, Sales: Chau-Carbide blank, Zigong Carbide rough.

我厂主要生产：钻石拉丝模，天然拉丝模具、聚晶拉丝模具、cd拉丝模具、硬质合金模具、拉伸模、螺旋模、冲压模、制钉模、搓丝板、涂粉模、直杆模缩杆模、合线模、气保焊丝专用模具（一般500公斤不偏差）、电焊条模具（送丝飞轮、斜轮、前丝眼、圆管刀、调直瓦块、涂粉模等）、电线电缆模具、正方模具、扁线模具、六角模具等以及高科技拉丝粉，回收各种硬质合金，销售：珠洲硬质合金毛坯，自贡硬质合金毛坯。

Paper feeder,two pieces of upper and lower plate for die cutting, one set of allen key.

送纸机、模切上、下板各二件、六角匙一套。

This paper analyzed the expand ability of dish plate keel of the fore and after body of ship hull,compared several expand ing and forming methods,and put forward some advices about the application and some problems to which should be pay attention.

在分析了船体首尾部折角型龙骨板可展性的基础上，对几种展开和成形方法进行了介绍和比较，提出了应用的建议及应注意的问题。

Within Lower Plate rocks, there are numerous sub-parallel structures which often host gold and copper bearing breccias zones.

在下板岩石，还有许多分平行结构往往东道国黄金和铜轴承角砾岩区。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。