角条件

Some asymmetric vortex solutions are obtained, which yield the side forces and yawing moments having the order of magnitude agreeing with experimental data.

本文获得了大迎角旋转体在不同非对称边界条件下的非对称涡解，其中一些非对称涡解的侧向力和偏能力非符合实验数据的量级。

An approximate worm wheel hobbing method is derived from the study of the engagement, module and pressure angle of worm and straight gear in the case of no worm wheel hob and then an adjustment method is determined for correct engagement between worm wheel and worm with standard cutting hob, which is more valuable in practice.

在没有涡轮滚刀的情况下，通过研究涡轮蜗杆与圆柱齿轮的啮合条件，以及涡轮蜗杆与圆柱齿轮间模数、压力角的关系，推导出一种使用标准齿轮滚刀近似加工蜗轮的方法。

As above three condition can't be assure simultaneity,then Imput shaft and output shaft can't do instantaneous synchronization ,and no synchronization become more obvious along with fold angle of shaft's increase.

当上述三条件不能同时保证时，则输入轴和输出轴不能瞬时同步，随着轴折角的增大，不同步愈加明显。

The resolution is improved through optimal combination of bin attributes which are small offset, small bin, wide azimuth, large off-inline distance and high coverage. Then the "feature net" of near surface conditions was created, and the "sudden transition" of near surface variations was found to provide reliable foundation for optimum shooting parameters selection. The effective methods of spectrum analysis were generalized. It is concluded that the target is satisfying sand body interpretation, not pursuing high frequency.

通过较小炮检距、较小面元、较宽方位角、较大非纵距和较高的纵、横向覆盖次数等面元属性的优化组合，提高了该区地震资料的分辨率；建立了表层条件&特征网&，通过寻找表层变化&突变带&，可为最佳激发因素的选取提供可靠依据；总结了频谱分析的有效方法，提出要以砂体解释的需要为目标，避免陷入盲目追求高频率的误区。

This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.

本文利用有限元软件Marc，对开60°和50°V型坡口的平板对接接头，动态的模拟了单层单道打底焊，焊完一道后让试件冷却到室温以及单层单道满焊，每焊完一道后让试件冷却，然后再焊下一焊道，道间温度≤200℃，在以此为初始边界条件下开始下一道的焊接，真实的再现了焊接过程，得出了温度场，残余变形和残余应力场的分布规律，根据理论分析及经验公式验证了温度场以及残余变形的正确性，角变形的大小，这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较，验证了焊接残余应力的分布规律及模拟的正确性。

Based on finite element method,stiffness characteristics were investigated under different whirling angle, pedestal parameters ,and fit clearance,to present guidance for design of elastic ring.

本文针对两种弹性环刚度的计算方法——解析法和有限元法进行了对比，分析了各自的适用条件，并基于有限元法分析了涡动角、凸台参数和配合间隙对弹性环刚度的影响，为弹性环的结构设计提供了参考。

In the design of expension tool, the cone angle is the key, because it must satisfy the plastic extreme condition of the expension tube and reduce the upgoing frictional resistance of the expension cone to minimize the possibility of tool sticking. It is preferred that the material quality of expension tube must differs from that of casing and the yield limit of expension tube must be less than that of casing, which is favorable to protect casing.

在膨胀工具结构设计中，锥角设计是关键，除了要满足膨胀管达到塑性极限条件外，还应综合考虑膨胀锥上行的摩阻尽可能小，以减小工具卡死的可能；膨胀管的材质应与套管材质有差异为好，并且膨胀管的屈服极限应小于套管的屈服极限，这样有利于保护套管。

The effect of rake angle and cutting velocity on the shear strain imposed in the chips, microstructure and hardness of chips are highlighted in a variety of metals and alloys.

本文对比了不同的金属和合金在各种刀具前角和切削速度条件下，切屑上产生的剪应变、切屑的微结构及其硬度的变化规律。

In order to perfect the theoretical system of "tectonic control of hazard", this thesis researches the control function of stratum inclination of monoclinic structure, fold shape and angle between two limbs of fold, normal fault direction of dip and fault inclination, forms of faults combination over coal-mining-induced subsidence by means of theoretical analysis and numerical testing.

为了进一步完善&构造控灾&理论体系，本文从典型煤矿区的地质条件和开采实际出发，在以往研究成果的基础上，通过理论分析和计算机数值试验，重点研究单斜构造的地层倾角、褶皱构造形态及其翼间角、正断层倾向和倾角及断层组合对采煤沉陷的控制作用。

After vibratory load actings, the cohesive strength index and internal friction angle of the sample are decreased by 51.72% and 50% respectively; and the shear strength curve shifts down obviously under same testing conditions.

研究结果显示，在其他试验条件相同的情况下，经振动荷载作用后的红黏土试样黏聚力降低51.72%，内摩擦角减少50%，抗剪强度线向下显著偏移，表明振动荷载不利于红黏土的稳定和承载。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。