角形

With this method a model of the large offset, highly compact intake is made and tested meticulously at low and high speeds. In the paper the distribution of the total pressure at the exit section and the static pressure along the wall of the intake is given at low speed, and the performance of the intake has measured at different Mach numbers, incidences and yaws.

并借鉴S形进气道的设计方法完成了高偏距、短扩压埋入式进气道的设计，并对该埋入式进气道的高、低速性能做了细致的研究，给出了0.1马赫数下进气道出口截面上的总压分布、总压畸变、壁面静压分布，以及0.5～0.8马赫数范围内，该进气道模型在-7°～10°攻角范围和8°侧滑角范围内的性能。

The predicted amino acid sequence of the gene show a rather high homology(84.47% amino acid identities)with Haemaphysalis longicornis(H.longicornis) TnI (GenBank,GI:14041807).Furthermore, the actin-binding domains of troponin I in predicted amino acid sequence, just the same as H. longicornis ,at the amino acid residues 147-167, suggesting the gene is K haemaphysaloides TnI gene.

经同源性比较，该基因预测的氨基酸序列与长角血蜱肌钙蛋白Ⅰ(GenBank，GI：14041807)有很高的同源性(同源性为84.47%)，肌动蛋白结合位点位于147-167氨基酸处，且与长角血蜱肌钙蛋白Ⅰ肌动蛋白结合位点完全相同，表明该基因是镰形扇头蜱肌钙蛋白Ⅰ基因。

Located in the prospecting lines Nos.47 and 37-33 on the middle 270m section, the mineral typomorphic characteristics are as follows: pyrite possesses the combination of octahedron with pyritohedron, pyritohedron with octahedron, etc It appearsas hole-centre and mix center conduction, if being electron-centre conduction, the absolute magnitudes of thermoelectromotive force and thermoelectromotive coefficient of pyrite are bigger relatively; pyrite contains Cu; the relative absorbency in quartz D(subscript H2O0.9403, D(subscript CO2)0.1961, D(subscript CO2)/D(subscript H2O)0.2591 in prospecting lines 37-33 is smaller than average D(subscript H2O1.3267, D(subscript CO2)0.3090, D(subscript CO2)/D(subscript H2O)0.338 2 in the deposit.

江西茅排金矿区270m中段47勘探线及37~33勘探线的矿物标型特征为：黄铁矿形态见有八面体和五角十二面体，五角十二面体和八面体等聚形；出现空穴心型导电和混合型导电黄铁矿，若为电子心型导电黄铁矿，其热电动势和热电系数的绝对值相对较大；黄铁矿成分中检测出Cu；石英相对吸光度（37~33勘探线）D(下标 H2O)0.9403，D(下标 CO2)0.1961，D(下标 CO2)/D(下标 H2O)0.2591，略低于矿区研究样品的平均值D(下标 H2O1.3267，D(下标 CO2)0.3090，D(下标 CO2)/D(下标 H2O)0.3382。

Leaf sheaths glabrous; leaf blades linear-lanceolate, 3–6 × 0.3–0.7 cm, glabrous, apex acuminate; ligule rounded, tonguelike, ca. 1.5 mm. Racemes paired, 2–5 cm; rachis internodes thick, outer angle ciliate with long hairs, inner angles shortly ciliate or glabrous.

叶鞘无毛；叶片线形披针形 3-6 * 0.3-0.7 厘米，无毛，先端渐尖；叶舌绕行，舌状，大约配对的1.5毫米外消旋体，2-5厘米；不久的轴节间的厚，外部的角纤毛的具长毛，内部角具缘毛或无毛。

In possession of 20-year,s special productionand managerial experience,linking with the most advanced manufacturing engineering both at home and aboard,in the tenet of "uality First,Credit Highest"striving for innovation,and taking advantage of equipments and materials with high specification,high quality inJupan and Taiwan,etc.the orporation provide you high strength stainless steelmachine bolt,self tapping screw,trigonodont crew,setscrews of M2-M12 single-line slot,cross slot,inside and outside angle,pan head,conmbined screw,stainless steelspacer and special nut,such as stainlesssquare nut,hexagon nut,weld nut,welding yandage,folan screw nut,with annual output coming out in front of fellow industry.

公司拥有20年的专业生产及管理经验，融汇国内外最先进的制造工艺，力求创新，本着&质量第一，信誉至上&的宗旨，应用日本、台湾等高标准、高质量的设备及材料，为客户提供高强度M2～M12一字槽、十字槽、内外六角、盘头、沉头、尖头、平头等形状的不锈钢机械螺丝、自攻螺丝、三角牙螺丝、紧定螺丝；铝钉；全不锈钢铆钉、尾孔钉、子母钉；不锈钢垫片及不锈钢方母、六角螺母、焊接螺母、焊码、佛兰螺母等异形螺母，年产量名列同行业前茅。

Leaf sheaths glabrous or sparsely to densely pilose with tubercle-based hairs; leaf blades broadly linear, 5–20 × 0.5–1.5 cm, pubescent, rarely glabrescent, base rounded to subcordate, apex acute; ligule 1–2 mm. Racemes (2–)3–6 or more, mostly terminal, subdigitate, 2–9 cm; rachis internodes and pedicels broadly linear, triquetrous, ciliate on outer angle, shortly ciliate on inner angles.

叶鞘无毛或疏生在密被柔毛具基于小瘤毛；叶片宽线形， 5-20 * 0.5-1.5 厘米，短柔毛，很少脱落无毛，基部圆形到近心形，先端锐尖；叶舌外消旋体1-2毫米(2-)3-6或更多，主要末端，2-9厘米，subdigitate；轴节间和花梗宽线形，在外部角上三棱，纤毛，在内部角上不久纤毛。

The relationship of spring back angle with bending clearance and die shoulder radius in the U-shaped bending of Aluminum alloy sheet was investigated.

主要研究了铝合金板材 U形弯曲回弹角与弯曲间隙、凹模入口圆弧半径之间的关系，分析了不同厚度的板材弯曲回弹角的差异。

In order to increase the rolling capability of three-high cogging mill,the forging plant of Laigang reforms the traditional cogging process,joining the six angle-square pass with box pass well and designing the six angle pass with heavy elongation to realize conjugate rolling,thus realizing the heavy reduction,heavy elongation for cogging rolling and single end product outing and self nip,improving the rolling rhythm.

为提高三辊开坯轧机的轧制能力，莱钢锻压厂对传统的开坯工艺进行改造，将六角—方孔型与箱形孔良好衔接，并设计了能够共轭轧制的大延伸六角孔，从而实现了开坯轧制大压下、大延伸，以及成品单出与自动咬入，提高了轧制节奏。

By way of research, the profile curve of offset translating follower plate cam for realizing zero degreed pressure angle was explored.

压力角越小传力性能越好，经过研究，探索出了在推程中实现零度压力角的偏置直动从动件盘形凸轮轮廓曲线。

Specialized in manufacturing GB screws, pan head screws, lock tool screws, furniture screw, hex socket screws, nuts, carriage bolts, special bolts, pins, plain head hex socket screws, rivets, sphere screws, truss head screws, set screws, various bolts and non-standard screws.

专业生产各类国标螺丝；盘头螺丝；锁具配套螺丝；家具配套螺丝；内六角螺丝；螺母；马车螺栓；异形件螺栓；销；平头内六角螺丝；对扣螺丝；铆钉；球面螺丝；大扁头螺丝；各种非标；各种螺栓；紧定螺丝

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。