角分布

Theoretically the approximate conditions of the surface wave diffraction were analyzed,and the corresponding analytic expression of angle width of diffraction patterns was derived,which explained the asymmetry distribution well.

理论上对表面波衍射的近似条件进行了分析，得出了各级衍射条纹角宽度的解析表达式，解释了衍射条纹的非对称分布。

Tilt angle and twist angle of director with applied voltage at certain δ/λ are calculated with finite-difference iterative method.

根据这些方程和边界条件，利用差分迭代方法计算出指向矢倾角和扭曲角对应某一个δ/λ值在不同电压下的分布。

The mutual coherence and angular correlation function of scattered wave from two dimensional non-Gaussian rough surfaces is deduced using the Gram-Charlie distribution, then the pulse scattering from two dimensional rough sea surface is calculated, and pulse broadeding is discussed.

基于Gram-Charlie分布函数并利用三阶统计特性推导出了非Gaussian二维粗糙面的双频互相关和角相关函数的计算公式，并以二维海面为例计算了其对几种典型波形脉冲的散射，讨论了脉冲展宽效应。

Angular distance distrubution-based search-less algorithm for star list.

基于角距分布的星表快速查找算法。

The measurement of roughness parameters of workpiece surface using the technique of light angular scattering distribution has been developed recently.

一、引言在工件表面粗糙度参数的测量中，光的角散射分布方法是一种有发展前途的测量技术。

The angular distribution of scattered lights almost kept the same in all azimuth direction.

散射光能量分布沿方位角的变化不大。

Based on the relations of the diffraction field and the surface wave, which conclude diffraction factor and interference factor, some relations were conformed such as: the diffraction fringes spatial distribution versus surface wavelength, the fringes half angular width versus the numbers of surface wave covered by laser spots and incidence angle, diffraction intensity versus surface wave amplitude.

通过对衍射因子和干涉因子的分析，得到衍射条纹空间分布与表面波波长的关系、条纹的半角宽度与入射激光光斑覆盖表面波的个数和入射方向的关系、衍射光强度与表面波振幅的关系，并解释了条纹缺级现象。

Based on the complex potential method about the plane theory of the elasticity of an anisotropic body,stress distributions in the plate with multiple cracks are obtained by using the conformal mapping and the Faber series expansion.

采用各向异性体平面弹性理论中的复势方法，应用保角映射技术和F aber级数展开，导出在任意载荷作用下多裂纹板应力场的级数解，引入当量屈服应力修正裂尖塑性区，并利用Sw ift韧带屈服准则建立含共线分布多裂纹结构的剩余强度分析模型，计算结果与试验结果吻合较好。

Based on the complex potential method about the plane theory of the elasticity of an anisotropic body, stress distributions in the plate with multiple cracks are obtained by using the conformal mapping and the Faber series expansion. The equivalence yield stress considers the effect on plastic zones. The Swift strip yield criteria is used to predict the residual strength of plate containing multiple collinear cracks.

采用各向异性体平面弹性理论中的复势方法，应用保角映射技术和Faber级数展开，导出在任意载荷作用下多裂纹板应力场的级数解，引入当量屈服应力修正裂尖塑性区，并利用Swift韧带屈服准则建立含共线分布多裂纹结构的剩余强度分析模型，计算结果与试验结果吻合较好。

The change of the cup anteversion angle can not affect the load distribution in the acetabulum,therefore the cup abduction range of 40°-50°can be confirmed as the safe range for cup implantation.

臼杯外翻角在40°～50°的范围内，假体-骨界面间的应力分布均匀，不存在因臼杯位置的不同而出现的应力过大或过小区，是臼杯置入理想的安全范围。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。