角位置

The method of setting up an affine coordinates system to solve the problems for the spatial crank and rocker mechanism is proposed.

分析并回顾了在给定摇杆两个极限位置及行程速度变化系数的情况下，最小传动角为最大的平面曲柄摇杆机构和空间曲柄摇杆机构的设计问题。

Ample air for combustion and brake cooling is achieved through large intakes positioned in the lower forward corners.

燃烧和刹车冷却充足的空气是通过在较低的位置向前角大口。

This semi-analytical method is accurate and widely used. It overcomes the limitation of the analytical solution such as conformal mapping. The position of cracks can be arbitrary.

这种解析数值相结合求解应力强度因子的方法，充分利用了解析方法精度高和数值方法适用性广的特点，同时又克服了保角变换等解析解的局限，各裂纹位置可以是任意的。

Test should be proceed under good meteorologic conditions and sea condition, Keep the cruise、ship speed and main engine revolution of the vessel stable before trial, Rudder angle should keep at center position.

试验应在良好的气象条件和海况下进行，试验前，应保持航行、航速以及主机转速的稳定，试验期间，舵角应保持在正中位置。

TPS the throttle valve position perceptron, this equipment might provide accelerator's immediate material to come with material and so on speed by engine revs to make the comparison judgment at that time engine's load conditions, adjusted engine's ignition angle of advance, obtained the good combustion efficiency, obtained the high power, and could achieve the province oil the effect, but the cost more then CDI .

TPS节流阀位置感知器，此装置可以提供油门的即时资料来跟引擎转速等资料作比较判断当时引擎的负荷状态，调整引擎的点火进角，来获得较佳的燃烧效率，获得较高的动力，并能达到省油的效果，但是成本比CDI来的高。

The mechanism that the newly woven-in weft drives the receded weft to be beaten tight again during beating-up is analyzed. The process calculating back-side warp angles of receded wefts at tightened position is presented, and then a formula of displacement that receded weft slips from receded position to tightened position is given.

分析在被钢筘打入织口的过程中新织纬驱使回退纬纱重新打紧的机制，说明回退纬纱被重新打紧时其后侧经纱角的计算流程，进而给出了回退纬纱从回退终了位置运动到打紧位置的位移算式。

III. If there is an expander roll, it can not be installed in the place of the tight roll of paper machine; instead, it should be adjusted to the first sink roll where the cornerite is comparatively small after pressurization, otherwise corrugations might occur.

如有展毯辊，展毯辊不能安装在纸机张紧辊的位置，而应调整到出压榨后，毛毯包角较小的第一根导辊的位置，否则易造成毛毯打折。

It is indicated that this loss will not change with the increase of the Reynolds number but the intensity of the passage vortex increases with the decrease of the Reynolds number. The tip leakage flow will weaken with the increase of the passage vortex because of the interaction between the passage vortex and the tip leakage vortex, and the position of the tip leakage vortex is more close to the middle of the passage. In addition, the distributions of the total pressure loss and the flow angle at the exit of the cascade are influenced by the intensity and the position of the tip leakage vortex.

结果表明：对于间隙存在造成的流动损失，数值模拟结果与实验结果及 Denton的预测值都十分接近，基本上不随着雷诺数的变化而变化；但是，随着雷诺数的减小，通道涡增强；间隙泄漏涡在和通道涡的相互作用中，强度减弱，在叶栅出口处的位置更加靠近中叶展；出口处的总压损失和气流角的分布也由于间隙泄漏涡强度和位置的变化而发生改变。

The effect of the stator magnetic saturation due to variation of the rotor position is considered by the scheme. Using estimated velocity of rotor corrects the rotor position.

该方法考虑了永磁转子位置变化对电动机磁路饱和的影响，采用转子转速的估算值对转子的位置角进行校正。

Jiaxing new angle Machinery Manufacturing Co., located in the Yangtze River Delta's economic development center in Hangzhou West to East by Shanghai, Xuzhou north and strategic location, convenient traffic, is China's Flocking base.

嘉兴市新兴角机械制造有限公司，座落在长江三角洲经济发展的中心位置，西往杭州、东靠上海、北接苏州，地理位置优越，交通便捷，是中国的植绒基地。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。