角位置

Proceedings from the theory of geometric optics,the condition adaxial noncoherent imaging of Fizeau opticalsynthetic aperture imaging system is derived to achieve diffracion limited performance over a finite field of view,and the conclusion is that the angular magnification of the individual telescope must be equal to the linear demagnification factor.

从几何光学理论出发，详细推导了斐索型光学合成孔径成像系统的近轴非相干成像条件，即子望远系统的角放大率等于系统的线性缩放因子。对于焦平面上的像点而言，合成孔径成像系统可等效为一个带有特殊形状孔径光阑的望远系统，这要求该孔径光栏的开口形状和位置分布与合成孔径成像系统各子系统孔径大小和位置分布相一致。

In order to resolve the conflict between excessive data storage, time expensive computation and real-time image processing, a method is proposed based on distance transfer with chamfer to extract the position and scale features of each objects, then a five points square predictor is used to estimate the position of objects next time and compute the velocity. Finally, objects are associated using improved weighed nearest neighbor. The algorithm is implemented on the platform of Xilinx XCV300E+ADI Blackfin 532 DSP.

为了解决多目标跟踪中数据存储量、运算量大与实时处理之间的矛盾，提出了一种基于倒角算子距离变换的多目标分离方法，分别提取出各个目标的位置和大小信息，再采用五点二次预测估计出下一场目标的位置从而得到目标的运动速度，最后由改进的加权最近邻算法进行目标特征关联。

Ultrasound biomicroscopean d gonioscopy were used to observe the position of the IOL haptics and anterior cha mber angle structure in patient who developed secondary glaucoma postoperatively.

方法收集25例(27只眼)行带虹膜隔人工晶状体植入术患者，分析手术疗效和并发症的发生情况，同时应用房角镜和超声生物显微镜观察术后发生继发性青光眼患者的房角结构和人工晶状体襻位置。

The result indicates, under the condition of big initial error and shell"s high speed rolling, after 60 seconds" flight alignment, the error of azimuth angle and attitude angle can be decreased to no more than 10 angle second, and the position and velocity error has been corrected. This shows the effective of our designed arithmetic.

研究结果表明：在初始误差较大、弹体高速旋转的条件下，经过60秒的空中对准，三个姿态角误差可降至10个角秒以下，同时位置和速度误差得到了修正，从而验证了算法的有效性。

The reason of feeding back in centrifugal bucket conveyer has been found through theoretical analysis of the position of discharging incline,initial discharging angle and final discharging angle in this article.

本文通过对卸料斜面的位置，初始卸料角及终止卸料角的理论分析，找出了离心式卸料斗式提升机的回料原因，求得最佳参数和料斗形状。

The fracture angle、height of roof coal and support chute which effect on the rules of caving coal are studied completely.

针对煤矿放顶煤工作面特点，建立了在有边界条件约束下的放出体多元数学模型，全面分析了顶煤垮落角、放煤高度、放煤口位置对放煤基本规律的影响，阐明放出椭球体轴偏角的产生与计算方法。

The simulation results show that the asymmetry structure of the ratchet die cavity influences the BMG's flowing behavior greatly. During the material filling tooth cavity, dead zone volumes exist and situate on the areas with sparse teeth distribution. The full filling or not of the ratchet tooth tips, as the final filling region of the forming process, determines the super-plastic forming quality. Adopting smaller punch speed or longer load holding time is necessary for full filling of the tooth tips.

研究结果表明，棘轮模腔结构的不对称性对材料的流动行为影响显著；在材料向齿形的充填过程中存在流动死区，死区的位置处于齿形分布较稀疏的部位；齿形尖角是成形的最后充填部位，在终成形阶段采用较小的压下速度或较长的保压时间，有利于齿形尖角的完全充满。

According to their respective functions,the main transmission mechanisms of a gun sight are analysed as being made up of four mechanisms viz.

根据功用，将某型号瞄准具主传动机构简化成4个机构：航路角装定器、升降角装定器、速度装定器和斜距离装定器，并对它们进行了位置和精度分析。

In this paper, the flux oriented angle of stator flux oriented vector control is deduced by the voltage vector space angle of the direct torque control, and mathematical model is set up based on the direct and quadrature axis component of the stator current.

将直接转矩控制与定子磁链定向矢量控制相结合，利用DTC中电压矢量的空间位置角，推导出SFOVC中的磁链定向角，然后根据旋转坐标系中的d轴和q轴电流分量，建立定子磁链估计的数学模型。

The handling stability is analyzed, mainly the steering transient response test of steering wheel step input、 the steering transient response test of steering wheel angle pulse input、 return-ability test、 steady static circular test and central steering test are carried out. With those test, how the front suspension system can influence the handling and stability performance is investigated.

在此基础上进一步建立了整车模型，包括前悬架系统、后悬架系统、转向系统、前轮胎系统、后轮胎系统、车身系统，分析了该车的操纵稳定性，主要进行了稳态回转试验、转向盘角阶跃输入、转向盘角脉冲输入、转向回正试验、转向盘中间位置转向试验，并通过这些试验来考察了前悬架对操纵稳定性的影响。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。