角位置

In this article, authors introduce data-getting methods of a shield attitude measure system composed of laser target, total station and PLC, and state calculation methods to get coordinates and angles of the shield machine with these measure data.

在利用盾构机进行的隧道掘进施工工程中，为了将掘进线路与隧道设计曲线之间的误差控制在一定范围内，需要及时测量盾构机的位置和掘进的方位角。

The location of separation line and relative the strength and position of avortex shed from a strake are present here.

机翼表面上震波及高攻角涡漩流所产生之分离流形式及强度与位置结果亦可正确地计算及分析。

At this time, loosen the connection screw of standard section with spanner, hang the shaft of hand crane on the upper angle bar, sway the shaft of hand crane upward, separate this standard section from the next section, and lay it in the suspension coop, dismantle the other standard section for the same method, and turn the shaft to another direction, draw the lifting wire rope tightly, the operation staff leave the suspension coop, open the lock stopping instrument, fall the suspension coop to next position and lock the brake instrument, the operation staff return to the top of suspension coop, continually dismantle note: forbid the staff leave on the top of suspension coop or in the coop when the suspension coop is running

8.1折除时，首先将吊笼用停层装置停靠在待拆除的标准节的下两节上，操作人员上到吊笼顶，卷扬机松绳，用小吊杆将顶梁略向上提起，拔出顶梁横销，使顶梁值得徐徐降下，降到拆除节下一节中间框架角处，并重新穿上横销，这时用板手将标准节连接螺栓松开，将手摇起重机小吊杆钩挂在待拆节上框架用钢土，到吊笼内，用同样的方法拆下另一节标准节，然后将吊杆转向不影响升降机运行的方向，收紧起升钢丝绳，操作人员离开吊笼，打开锁止机构，使吊笼下降到下一个拆除位置，并将锁止机构锁死，人员重返笼顶，进行下一拆除循环注意：在吊笼运行时绝不允许有人员留在吊笼顶部或吊笼内

When dismantle the machine, firstly, stop the suspension coop on the lower 2 sections of the standard sections, the operation staff go on the suspension coop top, the hoisting machine loosen rope, lift the pillar with small shaft, pull out the horizontal pin of pillar, let the pillar fall slowly to thedismantled section's middle angle bar, insert the horizontal pin again. At this time, loosen the connection screw of standard section with spanner, hang the shaft of hand crane on the upper angle bar, sway the shaft of hand crane upward, separate this standard section from the next section, and lay itin the suspension coop, dismantle the other standard section for the same method, and turn the shaft to another direction, draw the lifting wire rope tightly, the operation staff leave the suspension coop, open the lock stopping instrument, fall the suspension coop to next position and lock the brakeinstrument, the operation staff return to the top of suspension coop, continually dismantle note: forbid the staff leave on the top of suspension coop or in the coop when the suspension coop is running

8.1折除时，首先将吊笼用停层装置停靠在待拆除的标准节的下两节上，操作人员上到吊笼顶，卷扬机松绳，用小吊杆将顶梁略向上提起，拔出顶梁横销，使顶梁值得徐徐降下，降到拆除节下一节中间框架角处，并重新穿上横销，这时用板手将标准节连接螺栓松开，将手摇起重机小吊杆钩挂在待拆节上框架用钢土，到吊笼内，用同样的方法拆下另一节标准节，然后将吊杆转向不影响升降机运行的方向，收紧起升钢丝绳，操作人员离开吊笼，打开锁止机构，使吊笼下降到下一个拆除位置，并将锁止机构锁死，人员重返笼顶，进行下一拆除循环（注意：在吊笼运行时绝不允许有人员留在吊笼顶部或吊笼内

Of course, its location is an enormous help, sitting as it does on a promontory with water on three sides and the famous Sydney Harbour Bridge as a picture-postcard backdrop.

当然，这座建筑有着得天独厚的地理位置：它高踞一个呷角，三面环水，背景是著名的悉尼港大桥。

Cruise missile is sent to surface by underwater carrier in virtue of torpedo launching tube.

出于弹器分离、提高导弹命中概率及发射艇的安全性等需要，对运载器在出水时的运动速度、姿态角及位置等参数又都有严格的要求。

In this paper, we propose a new approach to recognize occluded objects. The information of the magnitude of the local extreme of the open angles in the contour of a model at a scale, the information of the distance and relative location between the two adjacent dominant points are suitably integrated as a set of features for describing a model, the features are invariant under rotation, uniform scaling, and translation of the curve.

该文提出了一种新的识别有遮挡目标的方法，即将目标模型和含有目标的遮挡图象的轮廓在某一尺度上张角的极值、极值点之间距离、相对位置等信息集成在一起，作为描述目标模型的一组特征，且这组特征在平移、旋转和均匀尺度变换下保持不变。

Sifu said "No need to place the tweeter at the every corner of nesting room".

在之前我不是说过师父说"在四周角头是不需要喇叭的"，所以我原本喇叭的位置如下图

Engineers can compare calculation results with the tunnel design curve in order to obtain deviation values of horizontal position, vertical position and angles of the shield machine, and can adopt these results to control tunneling operations of the shield machine.

隧道设计曲线是在城市三维坐标系中设计的，要得到盾构机掘进过程中的误差，就必须通过测量计算得到盾构机在绝对坐标系中的坐标位置和方位角。

Position and adjacent to two vertical plane surfaces meeting at a 90 ° angle, so as to

当玩具放在地板上任何位置，且靠在模拟房间的角落的两个相交为90 度角的垂直面时，通

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷