角位置

Other hardware in the angular measuring system is also analyzed and designed in detail.

本文还对组成角位置测量系统的其它硬件进行了详细的设计和研究。

After analyzing the characteristic of the rigid plane motion and the shortcomings of classical digital image correlation algorithms, the phase-angle position of the rigid body in the 2D image was characterized by 1D sequence signals using the method of equiangular sampling feature extraction based on circle windows. Then the generalized correlation algorithm for estimation of time delay based on wavelet transform was used to acquire the angular displacement. Finally the ultrasonic radiation force acted on the micro-component was determined by the relation between force and motion.

在研究检测对象刚体平面运动特点和分析传统数字图像相关算法局限性的基础上，采用基于圆周窗口等分角采样的特征提取方法，将二维图像中刚体的相角位置信息表征为一维采样时序信号，并通过基于小波变换的广义相关算法来估计位移前后特征序列的时延，得到刚体的旋转角位移，从而利用力与运动量的相互关系确定出作用于微构件的超声辐射力。

Methods The effects of the reading error and the misalignment of the probes on the accuracy of measuring and all the harmonics of roundness were analyzed; The strategy and the algorithm for optimizing the parameters of the measuring system were proposed; The distribution and propagation patterns of the measured errors for all the harmonics of roundness were studied in detail; A software for correcting the errors caused by the measurement error of the angle positions of the probes and the sensitivity difference between three probes was presented.

分析了测头读数及角位置误差对圆度各次谐波及圆周各点测量精度的影响；提出了三点法测量系统的优化策略与算法；研究了三点法测量误差的分布与传递规律；提出了克服测头定位误差以及3个测头的灵敏度不一致影响的软件校正方法。

There was 100% correlation between the position of the mandibular angle in the preoperative standing lateral radiograph and the intraoperative supine lateral radiograph, compared with 65% with the hyoid bone.

术前站立位颈椎侧位X线片与术中的仰卧位颈椎侧位X线平片之间下颌角位置的关联性为100%，相对应的是舌骨为65%。

So, this project adopts the realization scheme of double-pass raster monochromator plus direct drive and direct reading of the raster's angle position to control.

因此，本设计采用双通光栅单色仪加直接驱动直接读取光栅角位置控制的实现方案。

The primary axis measured parameter is an angular position read by a flexible position transducer that is mounted in a stainless tube with a radius of three feet.

主坐标轴测量参数是一个角位置由一个灵活的位置传感器是在一个有三英尺半径不锈钢管式阅读。

By applying the optimal tool parameters, the maximum tooth contact pressure is reduced by 45% and the maximum angular position error of the driven gear by 60%, in regard to the spiral bevel gear pair with a pinion manufactured by a cutter of straight-sided prole and of diameter determined by the commonly used methods.

通过应用参数的最佳工具，最大齿接触压力减少了45％，而最高的从动齿轮角位置误差60％，在关于由一个螺旋直齿轮刀具制造了一对锥齿轮双面形象和所常用的方法确定的直径。

The algorithm for optimizing the parameters of the measuring system were proposed; The distribution and propagation patterns of the measured errors for all the harmonics of roundness were studied in detail; A software for correcting the errors caused by the measurement error of the angle positions of the probes and the sensitivity difference between three probes was presented.

分析了测头读数及角位置误差对圆度各次谐波及圆周各点测量精度的影响；提出了三点法测量系统的优化策略与算法；研究了三点法测量误差的分布与传递规律；提出了克服测头定位误差以及3个测头的灵敏度不一致影响的软件校正方法。

When parallel laser beam is irradiating the bubble in the prism, circular interference fringe is produced in the far-field. Based on the far-field theoretical model, the angle position of interference fringes outside the prism is measured with spectrometer and converted into the angle position of interference fringes inside the prism according to Snell's law and then bubble diameter is calculated with computing software Mathematica, the relative difference of which is 0.2%.

平行激光束照射到棱镜中的气泡时，在远场将产生圆环状干涉条纹，利用气泡远场干涉理论模型，使用分光仪对三棱镜外干涉条纹角位置进行测量，由折射定律换算为棱镜内干涉条纹角位置，进而使用计算软件mathematica计算出气泡直径，其相对差为0.2%。

Angular position testing system is the reader-out unit of testing turntables, so theprecision of the whole system is depended on it.

角位置测量系统是转台系统的角位置读出装置，所以整个转台系统的控制精度就主要取决于测角系统的精度。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。