要求高精度的

Highly accurate approximations of the elliptic function are obtained in this paper through the use of Gauss transformation, which could not be obtained by the traditiona...

运用高斯变换法求椭圆函数的高精度近似值，解决了过去沿用椭圆积分表达不到精度要求的困难。

The paper mostly introduced control system of a new-type lab's hot-press which recently was researched and manufactured. It briefly described primary control principles of the press.

人造板现代热压工艺的研究需要高性能的实验热压机，该压机对压板的位置、速度和压力等热压参数的控制精度比生产型热压机的要求高，而且控制参数的调整范围也比生产型热压机大，所以，对控制系统的适应性和调节性要求较高。

This paper presents a feed forward and double-loop control technology of inverter,its double-loop control including a capacitor current inner loop control and instantaneous voltage outer loop control.

高质量的输出有两方面的指标要求：稳态精度高和动态响应快，即要求逆变器的控制系统具有很好的静态和动态特性。

At the same time, the method which feed can be adjusted with curvature of curve to implement the control of interpolation error in high speed and high precision is found.

同时为了保证自由曲线插补精度要求，提出了进给速度能随曲线曲率自适应调整，实现高速高精度插补误差控制的方法。

This article summarizes the electric log technology applying to low-resistivity, low-porosity, low-permeable pay zones and fractured reservoirs. To study the influence of drilling-mud invasion and pore texture to oil zone resistivity and its electric log response rule," in-time log " and pressure gradient log should beapplied.

今后要研究钻井液侵入与孔隙结构对油层电性质和电法测井响应规律的影响，采用"及时测井"和压力梯度测井等技术措施；测井计算饱和度技术已日趋成熟，但需采用高精度数控测井等先进适用技术和更精细的"岩心刻度测井"解释方法，进一步提高精度，以满足低孔、低渗储集层和裂缝型复杂岩性储集层的更高要求。

The incident angle of parallel light beam is hard to measure accurately in a large measurement range.A measurement method based on the optical vernier measuring principle,which is more accurate,is presented in this paper.

为解决平行光入射角度精确测量时，很难同时实现高精度和大量程两方面的测量性能要求的问题，提出了一种基于光学游标测量原理的大量程条件下的高精度平行光入射角度测量方法及测量装置。

With the increasing of transmiting current and reducing of the minimal discriminable voltage, the influence of geological interference becomes more evident, so it is very necessary to introduce feasible mathematical methods to direct and inverse calculation of TEM, such as ANN, GA. Via an experiment on a known-profile in a copper mine, it is validated that the flexibility of the system and feasibility of the interpretation software.

数据采集软件、后期处理解释软件的编制及解释精度问题由于发送电流的加大和最小可测电压的提高，在加大了勘探深度的同时，地质噪声和各种效应的影响将更加明显，从而对解释软件也提出了更高的要求，传统的数据处理解释软件不能满足要求了，因此有必要引入成熟的数学方法：如神经网络等，增加一维、二维的解释精度与速度，并对于特殊三维体作正演计算。

The design on the receiver of Strong Current Source TEM and the data collection system. In order to increasing the depth of exploration and enhancing the measure precision, it need to decrease the minimal discriminable voltage, besides increasing the current intensity. 3. the program of interpretation software and precision of interpretation.

强场源瞬变大地电磁系统的接收机及数据采集系统设计问题在加大工作电流的同时，尽量降低系统的最小可分辨信号电平，这就意味着探测深度与精度的相对增大与提高，这对数据采集系统提出了更高的要求，要求数据采集系统动态测量范围大，最小可测电压的能力与信噪比高。

With the help of recommended abrasives and techniques, through the process of heating – roughly hot rolling – precisely hot rolling in a variety a machines, hot rolls can be shaped into high-precision aluminium belts, which shall better meet the growing needs of the PS baseboards for pots and the simifinished aluminium foil sheets, for there is a big market gap and high grade request for high-precision aluminium belts in the market.

三、建设规模：年产40万吨高精度铝板带热轧卷；工艺技术：采用国际先进的热轧生产技术，由铸锭经加热—热粗轧—多机架热精轧的生产工艺，配合引进的工艺技术磨具可满足制罐料 PS 板基、双零铝箔坯料等市场缺口大的高精度铝板带产品对热轧卷的质量要求；主要设备：包括铸锭铣床一台、推进式加热炉3台、2400mm1+4热连轧生产线一条、轧辊磨床2台（国外引进1台），预计引进设备需用外汇8000万美元。

In order to attain high accuracy of GPS satellite navigation, positioning and low cost in precision agriculture, it is studied a method of GPS Pseudo-range observation and Carrier phase measurement to combine the actual conditions of agriculture. It is presented a method of high accuracy positioning and measure based on GPS OEM board in this paper, and proved the feasibility of key technology with emulations and field tests.

为了适应精准农业高精度、低成本的GPS定位导航应用要求，本文通过对GPS伪距和载波相位定位方法的研究，结合精准农业的实际情况，提出了基于GPS OEM板的高精度定位与测量方法，并用仿真和田间试验验证了各关键技术的可行性。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐