装入

Ailable in strong wooden drums of 1,2,5,10 and 20 litres.

这些货物分别装入1、2、5、10、20升的木桶里。

She bagged all the lef to vers.

她将所有吃剩的食物装入袋内。

Also, you would not need to try and redistribute the filling of the Air Pillow as you would with a normal pillow which are mainly filled with thick sponge, scraps of foam, cloth scraps or other fibrous material.

使用气枕后，当你疲劳或头痛时，由于气胆内装入了空气，你无需移动头部，找到让你舒服的睡姿，也无需重新调整枕头内的填充物，如海绵、棉肖、布碎等其他纤维物料，气枕能舒服地承托你的头部及头部外的部分体重。

Packaging:(1)In steel drum with inner double PVC bag containing 50KG net each.

包装：（1）双层塑料袋密封包装，每袋50公斤，装入铁桶内。

The first ball valve 3 into one, it is essential to stem the slot 4 with three goals.

12先将球3装入阀体1中，必须使阀杆4配入球3的槽中。

Ball valve 3 into 1, the stem must be made with four goals on the tank.

13将球3装入阀体1中，必须使阀杆4配入球上的槽中。

And a relative preparation is characterized in that according to mol ratio (0.8-0.975):(1.8-1.95):(0.010-0.15):(0.010-0.15) to prepare and mix Mg powder, B powder, C nanometer powder, and SiC nanometer powder uniformly to be filled into an iron tube or iron-copper composite tube to be sealed, rotationally forges, draws and rolls to obtain MgB2 superconductive material containing C and SiC nanometer powder, or tablets the raw powder mixed uniformly via a tablet press, to obtain MgB2 superconductive block containing C and SiC nanometer powder, arranges obtained band or block in a vacuum furnace, vacuums and fills argon gas, keeps temperature for 0.2-3h at 600-1200DEG C, and obtains MgB2 superconductive material containing C nanometer powder and SiC nanometer powder.

制备这种MgB 2 超导材料的方法，其特征在于，将Mg粉，B粉，C纳米粉，SiC纳米粉按照摩尔比(0.8-0.975)∶(1.8-1.95)∶(0.010-0.15)∶(0.010-0.15)配制并混合均匀，装入铁管或铁铜复合管中密封后，按顺序先后进行旋锻、拉拔、轧制，得到含C和SiC纳米粉的MgB 2 超导线材；或者将混合均匀的原料粉用压片机进行压片，得到含C和SiC纳米粉的MgB 2 超导块材；将得到的线带材或块材放置真空炉中，抽真空后充入氩气，在600℃-1200℃保温0.2-3小时，最终得到含有C纳米粉和SiC纳米粉的MgB 2 超导材料。

Blow the valve clean with compressed air.

卸下并拆开下降阀，用压缩空气将柱塞吹净，然后装入，重新安上。

Screws through the hole at the corner of the Box holder and 25mm.

3按照下面螺丝位置图的指示，将两粒3x40mm螺丝装入主机板保护套上，并分别套上25mm及3mm胶制丝母。

Bull gear and pinion gear are mounted in lower casing via bearing seat.

大小齿轮均采用渗碳淬火钢进行制造，并采用硬齿面加工方法加工而成，强度很高。小伞齿轮和大伞齿轮均通过轴承座装入下壳体中，两轴承座法兰下设有调整垫，用于调整齿轮副接触区的位置和齿侧间隙。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。