装上

An animation of a War Machine suit can also be seen in the closing credits with a Gatling gun attached on a shoulder.

一个战争机器的图片也出现在了结尾字幕的画面里，并且盔甲的肩部装上了格林机关枪。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

It went to all our hearts, I think, to leave them in that wretched state; but we could not risk another mutiny; and to take them home for the gibbet would have been a cruel sort of kindness.

我们在岛上无需再做什么了，我们把财宝装上了船，贮备了足够的淡水，把剩余的山羊肉也带走了，以防万一。

He lost an eye in an accident, and now has a glass eye.

他在事故中失去了一只眼，现在装上了一只玻璃假眼。

Eye He lost an eye in an accident,and now he has a glass eye.

意外事故里他伤了一只眼睛，现在装上一只玻璃做的假眼。

We'll see you here in three months. And I'll fit you for a glass eye.

那好吧，三个月后再见我到时帮你装上假眼

He lost an eye in an accident,and now he has a glass eye.

意外事故里他伤了一只眼睛，现在装上一只玻璃做的假眼。

Replaced the GPS with one of our own.

装上了我们的全球定位系统

Using the Grease Gun to fill in th e heat-resistant lubricating grease, then fasten the bolt and close the door.

打开侧门，旋下注油螺钉，用黄油枪加满耐高温润滑脂，旋紧螺钉，装上侧门

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。