表面粗糙的

The polishing fluid is composed of Al2O3 micropowder with a grain diameter of 0.5-1.0 mum, coal oil, lard, plant oil and spindle oil, wherein Al2O3 micropowder is abradant, coal oil is solvent, the mixing liquid of lard, plant oil and spindle oil is as additive; and the polishing fluid is prepared by a mixing liquid which is composed of 2% lard, 2% abraser, 8% plant oil and spindle oil by volume and 88% coal oil. The polishing fluid can produce the H62 brass element with a uniform surface quality and a good surface roughness value up to 0.008 mum, has the characteristics of no eroding elements, effectively relieving mechanical score, good processing surface quality and can be used for decoration of the plastic metal material and surface polishing process before the material metallographic microscope analysis.

抛光液由粒径为0.5～1.0μm的Al 2 O 3 微粉、煤油、猪油、植物油和锭子油混合而成；其中Al 2 O 3 微粉为磨料，煤油作溶剂，猪油、植物油和锭子油的混合液作添加剂；抛光液按体积比由2％的猪油、2％的磨料、8％的植物油和锭子油的混合液、88％的煤油配制而成；该抛光液能够加工出表面质量均匀，表面粗糙度值达到0.008μm的H62黄铜工件，具有不腐蚀工件、有效缓解机械刻划作用、加工表面质量好的特点，可以用于塑性金属材料的外观装饰性加工，以及材料金相分析前的表面抛光加工。

Such as angle grinder, wire brush, needle beam pneumatic rust, and wind knock rust hammers, gear-type rotary rust, etc., are semi-mechanized equipment, tools, light, mobility, and to more thoroughly to rust , old coatings, the coating can be played on the shelf hair treatment, significantly more efficient than manual derusting increased up to 1 ~ 2m2 / h, but can not remove the oxide skin, the smaller surface roughness and can not achieve high-quality surface to deal with quality, ergonomic handle lower than the jet.

如角向磨光机、钢丝刷、风动针束除锈器、风动敲锈锤、齿型旋转除锈器等，属于半机械化设备，工具轻巧、机动性大，能较彻底去除锈、旧涂层等，能对货架涂层进行打毛处理，效率比手工除锈大大提高，可达1~2m2/h，但不能除去氧化皮，表面粗糙度较小，不能达到优质的表面处理质量，工效较喷射处理低。

On this basis, we circumstantiate material removal mechanism of colloidal SiO2 polishing LBO crystal and formation of super smooth surface, and study the relationship among pH of the slurry and material removal rate and surface roughness.

在此基础上，对胶体 SiO2抛光 LBO 晶体表面材料去除机理和超光滑表面的形成进行了详细的描述，研究抛光液的 pH 值与材料去除率和表面粗糙度的关系。

Experiments were performed with this device to measure the static coefficient of friction for three kinds of material(45steel,HT35-61,QT80-2) in the same processing method,the same surface texture,the same load,dry friction and different surface roughness conditions respectively.

分别对材料(45钢、HT35-61、QT80-2)在相同加工方法、相同表面纹理、载荷恒定、干摩擦条件下，改变表面粗糙度时的静摩擦因数进行了测定。

The numerical relationship between the proportionality constant of surface roughness scattering mobility model and surface roughness degree is deduced.

推导出SiC表面粗糙散射迁移率模型的参数与界面粗糙度之间的数值关系。

However, in the temperature range of 1150-1300℃, the surface morphology of SiC coatings changes to rounded hillocks and the as-deposited coatings are very rough.

沉积温度和SiC涂层表面形貌的关系如下： 950℃时，沉积的SiC颗粒非常细小，为独立的球形堆积； 1000～1100℃时， CVD SiC涂层表面光滑、致密； 1150～1300℃沉积的SiC涂层呈现出球状或瘤状结构且表面粗糙。

Then CMP comes into being, combining the chemical and mechanical actions so as to realize the precise removal of the surfaces to reach the higher level of surface roughness and surface waviness.

化学机械抛光便应运而生，它综合了化学的和机械的共同作用，实现了对部件表面的精密去除从而达到较高的表面粗糙度和表面波纹度。

The results showed that, as a kind of anode corrosion inhibitor, BTA adsorbed on the copper surface and then funned a protective film by condensation reaction, and then decreased the corrosion current of copper by increasing the equilibrium potential.

结果表明。当H2O2存在时，抛光液中BTA作为阳极缓蚀剂吸附在抛光表面，提高了阳极铜溶解的平衡电位，并通过缩合反应生成保护膜，减小了抛光后的表面粗糙度，提高了表面质量，同时在一定程度上增加了抛光过程中的摩擦系数。

The bare cells with smooth surface presented transverse outspreading effect at mica surface. Great changes took place in surface roughness for those bacterial cells after metallization. A large number of nickel nanoparticles were observed to be equably distributed at bacterial surface after activation and subsequent metallization.

结果显示，空白对照菌表面平整光滑并在云母基底表面表现出较显著的铺展效应；经过活化和化学镀镍后的菌细胞表面粗糙度明显增大，并在基本保持原有菌模板外形的基础上，其高宽比有所增大。

Trim the gully shape error, reduce the bearing surface roughness, improve the physical and mechanical properties of bearing collar, improve the stress condition, reduce the surface of bearing vibration and noise

修整沟道的形状误差，降低轴承表面粗糙度，改善表面物理机械性能，改善轴承套圈表面的应力状态，降低轴承的震动、噪声

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。