英语人>网络例句>表面粗糙的 相关的搜索结果
网络例句

表面粗糙的

与 表面粗糙的 相关的网络例句 [注:此内容来源于网络,仅供参考]

By using the KDMRF-1000F MRF polishing machine and KDMRW-1 water based MR fluid,one K4 flat work piece (80 mm in diameter) and one K9 sphere work piece (145 mm in diameter) were polished,experiments show that work piece one has a peak-to-valley value of 55.3 nm and a root-mean-square value of 5.5 nm;and work piece two has a PV value of 40.5 nm and a RMS of 5 nm,which indicates that the surface roughnesses of two work pieces have been improved obviously.

实验显示,样件一面形收敛到PV值55.3 nm,RMS值5.5 nm;样件二面形收敛到PV值40.5 nm,RMS值5 nm;样件的表面粗糙度均有显著改善。结果表明,磁流变修形技术具有高精度、高效率、高表面质量的特点。

DFM three-dimensional phase picture of Ag layer showed that Ag layer stacked closely on surface of matrix, and its surface was scraggy.

DFM的三维立体相图分析表明:在环氧树脂表面激光诱导出的Ag沉积层呈紧密堆积,其表面粗糙不平。

The effects of phase offset deviation and intensity deviation on measurement, and the cut-off error of sinusoidal phase modulating function in phase shift interferometry are discussed and analysed.

本文将连续相移干涉技术、外同步控制技术和锯齿波相位调制技术,用于改造传统的光波干涉量法,实现了表面轮廓测量,成为一种有效的表面粗糙度评定和分析手段。

In this paper, the principle and hardware of test system are designed and the step motor's control software is designed at the same time. The assessing methods of linearity errors are analyzed and the test methods of linearity, diameter and roughness are provided and the corresponding softwares are programmed with VB. At last, the test method of roughness without touch-light scattering is proposed.

论文对检测系统的原理及硬件电路进行了设计,同时对步进电机的控制软件进行了详细的设计;对直线度误差的评定方法进行了分析,分别给出了炮膛内径的直线度、直径及阴阳膛表面粗糙度的测量方法,并用VB 编写了相应的控制软件,最后提出了一种炮膛粗糙度非接触测量法—光散射法。

The semi-ellipsoidal surface will be replaced by a hemispheroidal surface in the next device design. The required surface roughness of the metallic parts should be as low as =0.05μm.

下一阶段的人工椎间盘将以半球形面取代半椭圆球面设计,并且需提出加工制造与抛光处理流程,要求表面粗糙度达到=0.05μm以下,使表面间有较平顺的接触行为。

On the basis of micro surfaces redrawing, the surfaces were profiled through different directions.

在微观表面重现的基础上,对不同方向的表面粗糙度进行探测。

Not the transformation stress but the initial toughness is the controlled factor for the roughening behavior of free surface during plastic deformation. This phenomenon is discussed in terms of geometrical and physical effect of plastic deformation.

而且初始表面初粗度,而不是相变应力是控制表面粗糙化速率的主导因素;用变形的几何作用和物理作用对此进行了解释。

Because they have high precision and are fit for measuring soft materials, the easily scathed parts and some surfaces with some useful information.

在表面粗糙度非接触测量中,光学法是测量的主体,其测量精度高,适于对软质材料,易损工件,以及某些带有有用信息的表面进行测量。

Among the factors which have influence on scuffing failure,surface roughness and slidingspeed are very important.

在影响表面胶合失效的诸多因素中,表面粗糙度和相对滑动速度都非常重要,因此,利用改装的MHK500型环。

This body scrub eliminates dead surface skin cells, smoothes rough areas and stimulates the skin's surface.

这项全身的去角质护理,消除了皮肤表面死亡的细胞,刺激皮肤表面使皮肤粗糙区域平滑。

第10/46页 首页 < ... 6 7 8 9 10 11 12 13 14 ... > 尾页
推荐网络例句

I didn't watch TV last night, because it .

昨晚我没有看电视,因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。

I'm running my simile to an extreme.

我比喻得过头了。