表面

Bearing bore or outside the surface and the ferrule end face connected to a ring surface.

轴承内孔或外表面与套圈一端面连接的套圈表面。

In the influencing factors of yarn, the yarn of less diameter have lessfiloplume, as adding twist, the filoplume lessen, on the other hand, adding twist increases the tightness of fabric, make the filoplume of fabric moving back harder, aggravate theprickle to skin. The relationship between the prickle and twist is double curve.

竹原纤维纱线的捻度与刺痒感成双曲线关系，一方面纱线表面毛羽量随捻度的增加呈减少趋势，刺痒感下降；另一方面，捻度增加，纱线紧度加大，纱线表面毛羽受外力后避让困难，对皮肤的作用力加大，加重刺扎感。

On the other hand, having greater absorptivity is the key factor for filtrate reducer to control water filtering, for filterability can not be materially controlled by macromolecular being unable to be effectively absorbed on the surface of cement granules.

在水泥颗粒表面有较强的吸附能力是降失水剂形成堵塞失水通道机制的关键因素，不能有效吸附在水泥颗粒表面的高分子，无法实质性控制体系的失水。

The results show that dynamical ductil-ity dominated final velocity of fragments. During tube expansion, the shear fracture appears preferentially a-long the adiabatic shear bands under positive stress, so the adiabatic shear band determines the size and shapeof fragments. Though the fragmentation behaviour of medium carbon Si - Mn bainific steel is close to that ofsteel 50SiMnVB, medium carbon Si - Mn bainitic steel is an ideal candidate material for the tubular bombs be-cause it is better in dynamical ductility, which can enable the tubes to gain high speeds before fragmentation.

结果表明：材料动态塑性是决定破片最终速度的主要因素；圆管膨胀时外表面形成以剪切为主的裂纹，并向内扩展，接近内表面的绝热剪切带伴随着圆管的膨胀而扩展，并未出现失稳现象，但在正应力的作用下成为优先的断裂通道、决定破片的尺寸和形态；中碳Si-Mn贝氏体钢与50SiMnVB钢的破碎性能相近，但贝氏体钢动态塑性很更好，破碎前的膨胀量较大、更有利于提高破片初速，是弹箭比较理想的候选材料。

According to experts, wood veneer in the production of solid wood will be cut to about 2 mm thick pieces of wood, with a special adhesive, attached to the furniture surface, and then by painting, UV baked, characterized by a smooth touch, knock on wood buckle with a finger thick plate has a sense of clarity but the irregular surface of wood, in the plate corners can be vaguely seen around 1 mm veneer.

专家介绍，实木贴面在制作中将实木切成约2毫米厚的木片，经特殊粘连，贴在家具表面，再经上漆，紫外线烘烤而成，特点为触摸光滑，用手指扣敲木板有厚实感，表面木纹清晰但不规则，在板块转角处可隐约看见1毫米左右的木皮。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

After heated to the softening point, the flat glass receives a rapid and even cooling treatment on its surface, with the compression stress in outer part and tension stress inner part.

钢化玻璃是将平板玻璃加热到接近软化点时，在玻璃表面进行均匀的急速冷却，使玻璃表面产生压应力，内部为张应力，从而提高了玻璃的强度和热稳定性。

This is because the geometry of the surface of a globe, say, is fundamentally different from that of a flat surface.

这是因为，比方说球状表面的几何特征，与一个平坦的表面从根本上说是不一样的。

Cloths are safe to use on many surfaces effectively to remove tarnish, grime, and fingerprints on silver, gold, copper, bronze, flatware, brass lamps, tile, hardwood and many other surfaces.

布是安全有效地使用在许多表面，以消除损害，污垢，指纹和银，金，铜，青铜，餐具，铜灯，瓷砖，硬木和许多其他表面。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。