表面

TLC analysis of the ferment had classified the biosurfactant into glycolipid type. The diameter of oil displacement activity achieved 7.2 cm when use optimized medium. This biosurfactant had a good emulsification, the emulsified fluid could maintain at least 14 days.

排油圈分析和TLC分析表明，菌株E发酵液排油圈直径为7.2cm，表面活性剂为糖脂类生物表面活性剂；该生物表面活性荆叶菜籽油乳化能力校好，可以使乳化性能稳定保持14d以上。

By collecting images of fringes of equal chromatic order and comparing them,the influence of many factors on FECO and clearance calculation of surface forces apparatus,such as the distance between the object glass and the contact point,the grating constant of spectrometer,the angel between total reflection triple prism and the flat of inner beam path and so on,was analyzed.

通过采集图象进行对比分析的方法，讨论了表面力仪中物镜与接触点的距离、分光仪光栅常数、全反射三棱镜与单色仪光路光学平面夹角等因素对FECO条纹以及后续计算的影响，并介绍了表面力仪中计算表面间隙的两类主要方法。

Aim: To evaluate the surface hardness and abrasion resistance of die stone model with the application of a new gypsum surface hardener.

目的：测定涂布超硬石膏表面硬化剂有机硅树脂前后石膏模型的表面硬度和抗磨损性能，为该石膏表面硬化剂的临床应用提供依据。

Temperature difference between the center and the surface of hot rolled flat after rapid cooling results in heat transfer from the center to the surface, which causes the surface temperature rise in a short time.

热轧板带钢轧后冷却过程中，由于骤冷后表面与中心的温差导致轧件内部的热量传向表面，出现表面返红现象。

In this thesis, the AlN thin films were deposited on SiO2/Si and GaN/Sapphire substrates respectively for layered structure SAW devices by Helicon sputtering system. Laser ultrasound system was used to measure the acoustic wave velocity of AlN/SiO2/Si layered structure. Frequency response and insertion loss were measured by an HP8510C vector network analyzer to analysis insertion loss, sidelobe and quality factor. The results showed the possibility of incorporating thin films SAW devices with other semiconductor devices.

本研究使用回旋溅镀系统分别在SiO2/Si、GaN/Sapphire两种基板上沉积AlN并制作层状表面声波元件，并利用雷射超音波系统量测AlN/SiO2/Si结构之表面波速及机电耦合系数，再利用网路分析仪量测其频率响应，分析其插入耗损、 sidelobe、品质因子Q，以比较不同基材所制作之层状表面声波元件之特性，此研究成果初步验证AlN层状表面声波元件与半导体元件整合之可行性。

However, in the temperature range of 1150-1300℃, the surface morphology of SiC coatings changes to rounded hillocks and the as-deposited coatings are very rough.

沉积温度和SiC涂层表面形貌的关系如下： 950℃时，沉积的SiC颗粒非常细小，为独立的球形堆积； 1000～1100℃时， CVD SiC涂层表面光滑、致密； 1150～1300℃沉积的SiC涂层呈现出球状或瘤状结构且表面粗糙。

Cutting phaseWhen the protruding peak of holystone surface and coarse raceway surface is contacted, because osculatory area is lesser, the pressure on unit area is greater, below constant pressure action, holystone gets above all of workpiece " a traditional method of indicating the pronunciation of a Chinese character by using two other Chinese characters is cut " action, make the part of holystone surface grinds bead to fall off with disintegrate, show a few new grind bead and blade edge ......

切削阶段磨石表面与粗糙滚道表面的凸峰接触时，由于接触面积较小，单位面积上的压力较大，在一定压力作用下，磨石首先受到工件的"反切削"作用，使磨石表面的部分磨粒脱落和碎裂，露出一些新的锋利的磨粒和刃边。与。。。。。。

The main results of the investigation are as following:(1) Some important criteria for the design of multi-layer structure are acquired: the ratio of the layer thickness to the contact diameter should be controlled to a value about 0.8; increasing the number of the gradient layers and elasticity modulus of the top layer would benefit to the yield strength and the stress status at the interface.（2）By means of molecular dynamics simulations for a indentation and sliding process, it is discovered that dislocations of 45 direction to the surface occur in the surfaces layer, which is correspond to the direction of the plastic flows observed in the macroscopic continuous medium. The irreversible deformation caused by the dislocation and the atom piles at the surface are responsible for the irreversibility of the force response. They are also the main factors for the friction generation. The temperature and the indentation velocity have significant effects on the deformation behaviors of the material of the surface layer. The yield strength would increase obviously if the indentation velocity is greater than 10 m/s.（3）A method to evaluate the fracture toughness of coating by estimating the crack-density functionβof a Wicker''s indentation was proposed. Meanwhile a new surface treatment technology was developed using non-equilibrium plasma.（4）A MD-FE hybrid method and corresponding software was developed to analysis the tribological behaviors for multiplayer system.

研究主要内容和结果有：（1）得到指导梯度膜设计的几个准则：控制膜层厚度与接触半径比在0.8左右为宜；适当增加梯度层层数和顶层弹性模量，有利于提高抗屈服能力和改善界面处的应力状态；（2）通过对嵌入和滑动摩擦过程的分子动力学模拟，发现表层产生一个与宏观连续介质的塑性流动方向观测一致的45 方向位错；位错造成的不可逆变形和表面的原子堆积，是力的响应不可逆性的原因，也是构成摩擦力的主要因素；温度和嵌入速度对材料变形特性有显著的影响，当嵌入速度大于10 m/s时，屈服强度明显增加；（3）提出压痕裂纹密度系数β半定量判定膜层断裂韧性的方法；并开发出表面强化新工艺；（4）开发出分析表面摩擦学特性的MD-FE复合模拟方法和相应模拟软件。

The enhancement of the surface hydrophobic of modified wood was proved by the experimental results of hygroscopic coefficient and surface contact angle.

木材表面吸水率和表面接触角的变化证明，改性后木材表面的疏水性增强。

The solid immersion lens for near field optical storage has one negative refraction medium layer coated to the lower surface of traditional solid immersion lens to re-focus laser beam focused onto the lower surface of the solid immersion lens onto the surface of CD.

本发明公开了一种用于近场光存储的固体浸没透镜，在传统固体浸没透镜的下表面涂覆上一负折射介质层，该负折射介质层将聚焦于固体浸没透镜下表面的激光重新聚焦于碟片的表面。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。