补偿

On ultra precision lathe, author propose the principle of error in-process measurement and compensation of cylinder, end and contour, and use adjusted straightedge and sensor to build error on-line measurement and compensation control system of end turning.

研究了基于模糊数和插值原理的模糊控制算法，并用该算法实现了压电陶瓷微动刀架伺服系统的闭环控制，使其控制精度达到了±0.01μm；在超精密车床上，提出了圆柱面、端面和轮廓加工的误差在线测量与补偿原理，并利用标定的直尺和传感器建立了端面车削误差在线测量和补偿控制系统。

In order to reduce the effects of packet dropout on the system, a dropout compensator is added to the system, and a model for networked control systems with stochastic delays and dropout compensators is constructed, Based on this model, the sufficient conditions for the system asymptotical stability,γ suboptimum and optimum are given, and the output feedback control law for system H(subscript ∞) optimal control is obtained.

为了降低数据包丢失对系统稳定性的影响，在系统中增加了补偿器，并建立了具有丢包补偿器和随机网络诱导时延的NCS模型。在此模型的基础上，给出了系统渐近稳定和γ次优、最优的充分条件，并且获得了系统最优H控制的输出反馈控制律。

The method comprises the steps of: constructing a testing system which inputs digital codes and outputs simulated values of the analog-digital converter; obtaining a comparison table which is output through inputting responded simulated values of different digital codes from 0 to 2N-1 of the analog-digital converter; calculating to obtain an integration non-linear error comparison table corresponding to different digital code input of the analog-digital converter; compensating integration non-linear errors of the analog-digital converter through a hardware compensating method of adding a subtracter; and obtaining accurate analog-digital converter output.

搭建数模转换器的数字码输入-模拟值输出的测试系统；获得数模转换器从0到2 N -1的不同数字码输入响应的模拟值输出的对照表；计算得到数模转换器相应于不同数字码输入的积分非线性误差的对照表；通过加入减法器的硬件补偿方法，补偿数模转换器的积分非线性误差，获得准确的数模转换器输出。

Analysis of compensation features proves that the method is valid and feasible and has superior function.

补偿特性分析证明了该方案性能有效可行，是无功补偿的较好方案。

After groundwork of deep analysis of theory of symmetrical components the digital compensating algorithm used in SVC is reduced.

在深入分析了对称化补偿原理的基础上，推导出用于SVC的数字化无功补偿算式。

In the end, it gives weakness in this SVC system and inquires into improvement according to practical apply property.

最后根据系统运行情况，分析了补偿装置功能的实现，提出了该类无功补偿装置的不足之处和改进提高的方法。

This paper presents the principle of symmetry vector and introduces the design process of d-q vector controller.

通过分析对称分量法变换原理，以及在TSC+TCR混合型静止无功补偿装置中的应用，介绍了采用矢量变换控制的无功补偿装置的设计。

There is increasingly emerging the legal significance of the compensation system in the eminent domain largely due to the transformation of the takings\' system.

农地征收的补偿问题研究当下中国的城市化引发了大规模的征地，而目前的补偿机制导致大量失地农民的生产生活缺乏足够的保障。

Meanwhile,affected by the change of the environment tempera...

同时，由于压力传感器受环境温度的变化，对测量结果带来一定误差，温压补偿不可缺少，在设计中利用了数据融合的思想，提供了利用校验数据计算温度和压力的补偿关系的方法。

In the procedure of gymnastics athletes' U.C., the functions of the conditional ability performing now are more and more important in the competitive abilities of the floor exercises; besides the sport technique and conditional ability, one should pay attention to the figure in the pommel horse; the importance of the conditional ability is far above the sport technique , and the requirements of the figure are also high in the rings; the characters of competitive abilities of the vaulting horse are similar to those of the floor exercise, in which conditional ability plays a very important role; the requirements of the sport technique in the parallel bars are above those of the conditional ability; the requires of sport technique in the horizontal bar are strikely above those of other individual events, and the psychological ability is above the conditional ability; uneven bars contains much techniques, which means, sport technique is above the conditional ability; balance beam also contains much techniques and requires the least in the conditional ability in women's events, but this individual event demands psychological ability badly. Therefore one should emphasize on the cultivation the psychological ability when U.C. is applied to the balance beam.

体操各单项在实施非衡结构补偿过程中，自由体操各竞技能力中运动素质发挥着越来越大的作用；鞍马注重运动技术和素质外，还应注意形态要求；吊环中运动素质的重要程度远大于运动技术，对形态的要求也很高；跳马与自由体操的竞技能力特点类似，运动素质的作用非常大；双杠对运动技术的要求高于运动素质；单杠对运动技术的要求明显高于其它诸项要素，对心理能力的要求甚至略高于运动素质；高低杠技术性很强，对运动技术的要求高于运动素质；平衡木技术性较强，对运动素质的要求不如女子其他各项高，但对心理能力的要求非常高，在实施非衡补偿时，应注意对心理能力的培养。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐