行程

The flow capacity of large-size small Straight trip valve flow capacity is to install the pipeline flow capacity of valve scores, improve flow capacity is to increase the size of straight travel valve is usually larger than pipelines.

流通能力大尺寸小直行程阀的流通能力是安装阀的管道流通能力的分数，提高流通能力的方法是提高直行程阀的尺寸，通常可能比管道还大。

In order to prevent over-traveling when automating this type of valve, travel stops are used on air operators and limit switches on motor operators.

这类阀门在采用自动化执行机构时，为了防止出现超行程，在气动执行机构上要采用行程止动装置，在电动执行机构上要采用限位开关。

What straight poor performance, aiming to halt the stroke control valve, angle valve, prevent the travel of good performance?

什么直行程调节阀防堵性能差，角行程阀防堵性能好？

The direction of travel throttle valve angle is the horizontal direction, the level of flows into the medium, the level of outflow, easy to clean media is not removed, flow path at the same time simple and very little room for medium precipitation, therefore, prevent the valve angle stroke Deluge Valves, Fire Protection of good performance.

角行程阀节流的方向就是水平方向，介质水平流进，水平流出，容易把不干净介质带走，同时流路简单，介质沉淀的空间也很少，所以角行程阀防堵性能好。

One cycle of operation to take Silo body construction, the construction procedure as follows: steel banding to Silo body gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after Silo body pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

One cycle of operation to take construction, the construction procedure as follows: steel banding to gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

Equal percentage flow characteristics - ideal for the spool stroke of equal increments, changes in flow rate for the trip can be expressed as changes of flow in a constant percentage.

等百分比流量特性－理想地，对于阀芯行程的相等增量，流量对于行程的改变可以表示为在改变时的流量的一个恒定的百分比。

Using the smart card recorded data, the travel rate time per trip can be calculated, and the regulation of travel rate time by taxi can be fond from the cumulative taxi datum. In this paper, three new reliability indices and methodologies about travel rate time are developed, and Beijing transportation network reliability is analyzed by using these indices and the taxi trip datum.

本文以出租车车载智能卡采集的载客行程时间数据为基础，研究提出新的单位距离行程时间可靠性评价指标和方法，并使用该指标和方法对北京市路网的可靠性水平进行实例评价。

The company developed the "zero-pressure side of a long stroke piston engine" has been the use of new patents (ZL02228777.9); national invention patent applications,"a thermally efficient internal combustion engine piston long trip, technology and lateral pressure device"(Application No. 031283500) has entered the public procedures (Disclosure of CN1480633A) is the trial stage.

本公司开发的《零侧压长行程活塞内燃机》已经获得国家使用新型专利授权（ZL02228777.9）；申请的国家发明专利《一种高热效内燃机活塞长行程零侧压技术及装置》（申请号031283500）已经进入公开程序（公开号CN1480633A）的实审阶段。

The round trip is driven by servomotor, matched up with precision ball screw and wire slide rail, to smooth the round trip of the blade and position accuracy.

切刀与主轴采用无级变速AC马达。5。行程以伺服马达驱动，配合精密滚珠螺杆及线滑轨，切刀行程顺畅，定位精确。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷