螺钉孔

METHODS: Models of ALIF, PLIF and TLIF were simulated. After examination as normal group, the samples were randomly divided into three groups (n=5). Besides anterior, posterior and transforaminal lumbar interbody fusion include anterior, bilateral pedicle screw fixation was performed.

模拟临床手术建立前路椎间融合术、后路椎间融合术、椎间孔入路椎间融合术3种椎间融合术模型，先将所有标本作为正常对照组进行测试，然后将标本随机分为3组，每组5个标本，制成单纯椎间融合组，分别采用3种椎间融合术测试后，在此基础上再附加双侧椎弓根螺钉内固定进行测试。

To install the fixed filler on the corner cabinet, use a ф4.2MM drill to drill a hole on the bottom panel at a place near the fixed filler. Use pneumatic screwdriver to turn at the hole positions to form countersink holes. Use 4*50 self-tapping screws to secure the fixed filler on the bottom panel. Keep

转角柜固定封板的安装，先用ф4.2MM的直钻在柜底板靠近固定封板处打孔，/然后用风批头在打孔处转动几下形成螺钉沉孔，再用4*50的自功钉把封板固定在柜底板上/安装可调脚将柜底保持朝上，然后正面进入50MM画线并装好柜脚座。

The anatomic femoral attachment site of the FCL, slightly proximal and posterior to the lateral epicondyle, 20 was isolated, and an eyelet pin was drilled proximomedially across the distal femur through the center of the FCL femoral attachment site. A 7-mm reamer was then reamed to a depth of 25 mm over the eyelet pin, and a 7-mm bioabsorbable screw tap was used to tap the tunnel.

FCL在股骨外上髁后侧稍靠近端的解剖学附着点[20]离断，通过股骨FCL附着点的中心穿过股骨远端在靠内侧用小针钻孔，然后用7mm扩孔钻顺小钉扩至深度为25mm，使用7mm可吸收螺钉攻丝形成隧道。

In addition, on the main and the secondary support unit, screw-fixing holes for connecting with the pipe boards of an evaporimeter or inserting pieces for fixedly connecting with the pipe boards of the evaporimeter are provided.

另外，主支架单元和副支架单元上还设有与蒸发器管板连接的螺钉固定孔或与蒸发器发卡管固定连接的插片。

Principal products of our company: screw and nut for furniture, gharry screw, T type screw, loose joint bolt, flower basket bolt, expansion bolt, closing ring for bearing and aperture, Shanghai rivet, copper, iron and aluminum rivet, stainless steel standard pieces, flat key, pin key, automatic drilling nail, 12.9 level alloy steel hexagonal socket, tightening screw, countersunk head hexagonal socket screw, 10.9 steel structure bolt, machine bolt, firmware of DIN, ANSI, BS and JIS.

本公司生产和销售家具螺丝螺母、马车螺丝、T型螺丝、活接螺栓、花篮螺栓、膨胀螺栓、轴用孔用挡圈、上海拉铆钉、铜铁铝铆钉、不锈钢标准件、平键销键、台湾合资自攻自钻钉、12.9级合金钢的内六角、紧定螺丝、沉头内六角螺丝、10.9级钢结构螺栓、机螺钉、各种德标、美标、英标、日标紧固件。

To hold the keel in the box, barely screw in a long lock bolt with washer into the threaded hole on top of the trunk.

举行龙骨在方块中，勉强螺钉在长期锁螺栓与垫圈进入螺纹孔的上方的主干。

Tapping is the process of cutting a thread inside a hole so that a cap screw or bolt may be threaded into it.

攻丝是在一个孔中车出螺纹，以便装上有帽螺钉或螺栓。在那儿，戴着插有鸟颈毛的熊皮帽。

Power lines and power will board the connecting blocks, and then covered with electrical box and lock locking (Note: Do not pressure line), the final will be hanging hook screw into electrical boxes installed screw holes, tightening later M4 * 8 hanging hook-locking screw-tightening.

将电源线与电源板上的接线端子连接好，然后盖上电器盒并用锁扣锁紧，最后将吊勾拧入电器盒安装螺纹孔内，拧紧后用M4*8吊勾锁紧螺钉拧紧防松。

In 1929 some improvements were announced to what was now called the '33/8" Super Exe': the mandrel bore was increased to 1/2"(but 17/32" in reality, so allowing a 1/2" bar to pass clear through), the saddle carried a conventional compound slide rest with a T-slotted cross slide and swivelling top slide and, happily, the 10 tpi Acme-form cross feed screw had the outer flat rim of its handwheel engraved with a micrometer scale - an improvement mirrored simultaneously on the 4-inch lathe.

在1929年宣布了一些改进的话现在称为'33月8日"超级可执行'：在轴孔增加到1 / 2 "（但17/32 "在现实生活中，这样使1 / 2 "酒吧，通过明确的通过），鞍进行常规复合幻灯片其余的T型槽交叉旋转顶端幻灯片和投影片，并令人高兴的是， 10 TPI公司的Acme形式跨了饲料螺钉外单位辋其手刻有一微米尺度-改善镜像同时在4英寸车床。

That the cam-bore to valve/tappet dimensions are gauged with the head bolted to the block.

校对凸轮孔到气阀/凸子的距离时，顶盖已被螺钉固定在机体。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。