螺钉孔

Setscrew with access hole in bottom of housing. Move

螺钉孔与壳体底部的孔成一直线，转动主

The excellent and good rate was 89.13%. In the DHS, there were 2 cases with greater trochanter fractures, 1 case with over boring, 2 cases with pulmonary infections, 2 cases with urinary system infection and 1 case with coxa vara. In hollow pressing whorl bolt internal fixation, there were 1 case with coxa vara and 1 case with deep phlebothrombosis.

采用动力髋螺钉固定者术中大转子骨折2例，髋螺钉孔钻孔过深1例，术后发生肺部感染2例，泌尿系感染2例，髋内翻1例；采用空心加压螺钉固定者术后出现髋内翻1例，发生深静脉血栓1例。

The excellent and good rate was 89.13%. In the DHS, there were 2 cases with greater trochanter fractures, 1 case with over boring, 2 cases with pulmonary infections, 2 cases with urinary system infection and 1 case with coxa vara. In hollow pressing whorl bolt internal fixation, there were 1 case with coxa vara and I case with deep phlebothrombosis.

采用动力髋螺钉固定者术中大转子骨折2例，髋螺钉孔钻孔过深1例，术后发生肺部感染2例，泌尿系感染2例，髋内翻1例；采用空心加压螺钉固定者术后出现髋内翻1例，发生深静脉血栓1例。

Most of these plates have many locking screw holes designed to scaffold of raft the subchondral areas.

绝大多数这些钢板带有铆钉在软骨下区域的锁定螺钉孔。

Wraps the bottom is a ring, the jacketed wall to the upward contraction tube, the tube cavity cross section diameter is equal to or be smaller than inward wraps the thermos pot bottom diameter, the jacketed wall upward pinch-out, interacts the part in a set of bottom and the jacketed wall, digs out some inclined half circular slot, wraps on the bottom to open 2-4 reservation spiral nail hole.

套底为一个圆环，套壁为向内向上收缩的筒，筒腔断面直径等于或小于所套热水壶壶底直径，套壁向上尖灭，在套底与套壁交结的部分，挖出一些倾斜的半圆槽，套底上开2—4个预留螺钉孔。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

Remove vent from the roof and drill all screw hole locations with a 1/16 pilot hoe .

从roof上移开vent并用1/16的钻头将所有螺钉孔的位置都钻出来；注意：7。

Failures of cementless cups include accelerated polyethylene wear, malfunction of the locking mechanism of the polyethylene liner in the metal-backed shell,59–62 and extensive periacetabular osteolysis.63 Screw holes in the shell enable debris to access the periacetabular cancellous bone, a further extension of the effective joint space.

非骨水泥型髋臼杯的失败原因包括聚乙烯磨损加速，金属杯中聚乙烯内衬锁定机制失效和广泛的髋臼周边骨溶解。金属杯中的螺钉孔为碎屑进入髋臼周围松质骨提供了通道和更广的有效关节容积。

This special heat-treatment ensures full bearing performance and prevents the set screws from loosening during operation as the set screws can be tightened hard enough without causing broken inner ring set screw hole.

内圈螺钉孔周围经局部高温回火后，轴承获得更好的性能，可防止螺钉在轴承工作期间松脱，同时螺钉拧得紧也不会导致内圈爆裂。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。