螺钉

Objective: To investigate the possibility of CT-guided percutaneous fixation of cannulated lag screw on sacroiliac joint for treatment of pathologic pain of sacroiliac joint.

目的：探讨在CT引导下经皮微创技术置入空心拉力螺钉治疗病理性骶髂关节疼痛。方法：骶髂关节转移肿瘤患者8例，男4例，女4例；年龄12~83岁，平均53岁。单侧转移5例，双侧3例。肺癌2例，乳腺癌1例，卵巢癌1例，非霍奇金淋巴瘤1例，横纹肌肉瘤1例，骨髓瘤1例，前列腺癌1例。

METHODS: After treatment with percutaneous CT-guided fixation of sacroiliac joint with cannulated lag screw, the sacroiliac joint of the 8 patients became pathologically unstable.

对8例骶髂关节转移肿瘤患者试行在CT引导下经皮微创技术置入空心拉力螺钉稳定病理性骶髂关节不稳。

If trip-under stop happens in shifting from higher to lower gear position,screw out the upper adjusting screw.

如果跳闸停止下发生的转变，以降低较高的齿轮位置，螺杆上的调整螺钉。

If trip-under stop happens in shifting from lower to higher gear position,screw out the lower adjusting screw.

如果跳闸停止下发生的变化从低到高齿轮的立场，螺杆出较低的调整螺钉。

Screw off screw 10, remove the gear box.

3拧掉螺钉10，拆下齿轮箱。

Put the electric actuator to the closed position, fixing valve mandrel and electric actuator with coupling and screw bolts

将电动装置转到关闭位置，用连轴器和螺钉将阀门芯轴和电动装置输出轴固定

Demolition of the fractional coupling: first coupling screw Hexagon screw fixation, the re-coupling half gently to slow down from the shaft.

拆对分式联轴器：先把联轴器的固定内六角螺钉拧下，再轻轻把联轴器的一半从轴上慢慢拉下。

Mounted coupling: first in the motor shaft mounted on the head ring, mounted on coupling half, and then in the shaft coupling client and loaded block chute and Plum wrench tightening bolts (lifting shaft 3 ~ 5 mm and to provide mechanical seal prestressed); and then loaded up the other half on the coupling screw Hexagon screw must be tightened.

装联轴器：先在电机轴头上装上挡圈，装上一半联轴器，再在泵轴端和联轴器槽内装上挡块并用梅花扳手拧紧螺栓（吊起泵轴3~5毫米并提供机械密封预应力）；再装上另一半联轴器拧上内六角螺钉必须拧紧。

Mounted coupling: first in the motor shaft fitted with ring head, fitted with coupling half, and then end in the shaft and the coupling block bed fitted with Plum wrench tightening bolts (lifting shaft 3 ~ 5 mm and pre-stressed mechanical seal); and then loaded onto the other half of the coupling screw Hexagon screw must be tightened.

装联轴器：先在电机轴头上装上挡圈，装上一半联轴器，再在泵轴端和联轴器槽内装上挡块并用梅花扳手拧紧螺栓（吊起泵轴3~5毫米并提供机械密封预应力）；再装上另一半联轴器拧上内六角螺钉必须拧紧。

Check tightness of 5mm set screw in Steering Collar Clamp with the same 2.5mm hex.

检查紧定螺钉5毫米的指导领夹同2.5毫米十六进制。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。