螺钉

I coated the outside of the bearings with epoxy and pressed them in with an arbor press(a vice, or hammer should work fine too), as deep as possible so that I could still tighten the set screws.

余涂层的外部轴承环氧树脂和压制他们的安娜堡新闻（副主席，或锤应该也没关系），深使我仍然可以加强紧定螺钉。

The pothole fractured a bolt on the axle.

壶穴使车轴上的一只螺钉破碎。

Press the axle end to the bottom, draw the brake wheel 2, and make it close to the tape of behind cover, revolve the nut 5 clockwise, make it touch with the brake wheel, continually revolve the nut for one to one and a half ring, lock the screw and wind window.

4顺轴下压转轴端部至底，提取制动轮2使其制动环与后端罩3锥面贴合，顺时针方向旋转锁紧螺母5，使其与制动轮端面接触，再将锁紧螺母继续按顺时方向转一圈至一圈半，上好锁紧螺钉和通风窗，调整完毕。

In this type of initial jewelry, it is the ball ends which screw into the bar rather than vice versa.

在这个初步首饰类型，它是球结束对酒吧的螺钉，而不是相反。

Bell-type furnace from a shrouds,two furnace Block,two in the hood,a componet cooling enclosures,shrouds-rolled steel used welding of molding,using energy-saving lining all the latest technology fiber module structure,for the Top All Permian High-pressure wave fiber Banding hanging flattened,high aluminum screw linked with resistance bands Top fast-cooling cooling installation Double doors.

罩式炉由一台加热罩、两台炉座、两台内罩、一台冷却罩组成，加热罩采用钢板卷制密焊成型，炉衬采用节能型最新技术全纤维模块结构，炉顶为全纤维波浪叠法高压捆扎吊平顶，高铝螺钉挂装电阻带，炉顶安装双孔快冷降温门。

Bell-type furnace from a shrouds,two furnace Block,two in the hood,a componet cooling enclosures,shrouds-rolled steel used welding of molding,using energy-saving lining all the latest technology fiber module structure,for the Top All Permian High-pressure wave fiber Banding hanging flattened,high aluminum

罩式炉由一台加热罩、两台炉座、两台内罩、一台冷却罩组成，加热罩采用钢板卷制密焊成型，炉衬采用节能型最新技术全纤维模块结构，炉顶为全纤维波浪叠法高压捆扎吊平顶，高铝螺钉挂装电阻带，炉顶安装双孔快冷降温门。

Between cover and shell body is arranged seal washer fastened by stainless screw.

盖与壳身之间设有密封圈，并用不锈钢螺钉紧固。

Natural aluminium, for 10mm boring in connection with torx head screw

铝合金，用于梅花头螺钉M1611/20与10mm的钻孔连接

By inner diameter micrometer, add technical screw to the both ends of the stern tube at point A、C in order to make them the base of boring rod alignment.

通过内径分厘卡的测量，将A、C两个点上的基准功能分别转往各个对应的工艺基准螺钉上去，使他们成为镗杆校中的依据。

The support bracket foot can rotate in 360 degrees round the screw.

支架脚可围绕螺钉作360度旋转。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。