螺钉

Stainless Steel Self-drilling self-tapping screws, all kinds of self-tapping, machine screw.

不锈钢自钻自攻螺钉、各种自攻、机螺钉。

Bearing and shaft fastening methods are: the outer sleeve with eccentric spherical bearing, the eccentric sets Presentation at the bearing inner ring of the eccentric stage, along the axis of rotation direction of tightening eccentric sleeve, and then wrench tighten the screw Hexagon eccentric sleeve on the set screws can be.

轴承与轴的紧固方法是：对带偏心套的外球面轴承，将偏心套套在轴承内圈的偏心台上，沿轴的旋转方向拧紧偏心套，再用内六角螺钉扳手拧紧偏心套上的紧定螺钉即可。

Do not let screw head protrude the track surface.

用所配ST4.2螺钉试装，使螺钉头部不突出导轨表面。

Test-install with ST4.2 screw sets. Do not let screw head protrude the track surface.

用所配 ST4.2螺钉试装，使螺钉头部不突出导轨表面。

Press-fit components avoid the need for screw placement, which carries the added risks of neurovascular injury and fretting wear between screw and shell.

假体压配式固定避免了螺钉的使用，因为其会导致血管神经损伤以及螺钉和臼杯磨损的风险。

Pumps installed in the rolling bearing for the motor, bearings should be removed outside the cover, and then release the fastening screw cover and base shell and cover the seams to do a good job marking (both before and after the end of tag should not be covered the same), will cover the unloading of the fastening screw screwed into the expertise of the Motor Cover Screw in the two settings will be the top cover.

水泵中对于装有滚动轴承的电机，应先拆下轴承外盖，再松开端盖的紧固螺钉，并在端盖与机座外壳的接缝处做好标记（前后两个端盖的标记不应相同），将卸下的紧固端盖的螺钉拧入电机端盖上专门设置的两个螺孔中，将端盖顶出。

The main products have pressure riveting nut, compression nut riveting columns, inlaid into the nut, rivet nut up, riveting pressure screw, rivet pull screws, loose screws, etc.

主要产品有压铆螺母，压铆螺母柱，镶入螺母，涨铆螺母，压铆螺钉，拉铆螺钉，松不脱螺丝等。

In torsion , every groups have obvious effect of the stability of plate and screw structures. At 2.142°,the rigidity of A group is least and the rigidity of E group is most.

在扭转试验中，相同的钢板长度，一定螺孔间距，不同的螺钉数量对钢板螺钉内固定结构系统的稳定性有显著影响。

All kinds of screw cap, plain cushion, machine screw nail, fiberboard nail and hex wood bolt.

各种螺帽、平垫、弹垫、机螺钉、自攻钉系列、纤维板钉、六角木螺钉等配套。

Are required, please loosen screw 4 and move gear 3 to the position corresponding to the certain revolutions of

当需要某种圈数时，只要将紧定螺钉4 松开，移动齿轮3 至圈数数表1 的对应位置，旋紧紧定螺钉4即

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。