螺纹孔

With the extensively use of the spiral fluted taps with a large diameter in our country drilli...

随着大直径螺旋槽丝锥在我国广泛应用，在难加工材料表面加工大螺纹孔变得越来越容易。

Gibs are to have jacking threads in two holes per gib. These components must be installed in machined pockets, and bolted from the parting line surface.

每个镶条都有两个定位的螺纹孔，这些部件都比须安装到加工好的槽内，并从分模线面起固定。

To hold the keel in the box, barely screw in a long lock bolt with washer into the threaded hole on top of the trunk.

举行龙骨在方块中，勉强螺钉在长期锁螺栓与垫圈进入螺纹孔的上方的主干。

The headstock uses standard spindle, it support from the first kind tapping explorator organization to tap and use it to guarantee screwed hole location accuracy.

主轴箱采用标准主轴，借助第一类攻丝靠模机构对其进行螺纹加工从而保证螺纹孔的位置精度。

Tapping screws may be tested using pre-threaded holes in test plates to achieve screw failures instead of thread strippage.

自攻螺钉应装入带有螺纹孔的试验圆板上拧至螺钉损坏，而不是在螺纹测试条上进行。

The purpose of the gross and the clamps design for assailing silk on the body crest face of the D3115 diesel engine machine is to be accord with the size request of 43,83, and 71 when processing the 14 threads.For satisfying the request of producing rate,and because of the number of the threads is numerous.we adopt the single work form combination machine to carry out processing of the threads.

D3115，柴油机机体顶面攻丝机床总体及夹具设计的目的是使在3115柴油机机体上加工14个螺纹孔M14-6H时，在14个螺纹孔间符合43、83、71尺寸要求，且为了满足生产率的要求，顶面的螺纹孔数量较多，特采用立式单工位形式的组合机床对多孔进行攻丝加工。

Conductive thread of a hole without cutting tapping new technology to solve the past conductive thread easily slip teeth of the defects.

导电件螺纹孔采用无切削攻丝新工艺，解决了已往导电件螺纹容易滑牙的缺陷。

The modular machine tool is used to tap 18 screw holes of M8 and M10 on the left, 15 screw holes of M8, M10, M12 on the right and three screw holes of Z1/4, a screw holes of G3/8 on the back surface. The modular machine tool uses the horizontal-type single location three-side processing plan, the processing and assembly technology capability is good, and it clamps conveniently.

同时采用机械滑台，一次装夹，对左面15个M8-7H深14和3个M10-7H深15的螺纹孔，右面7个M8-7H深14，3个M10-7H深15，5个M12-7H深20的螺纹孔以及后面3个Z1/4&-5H深20和1个G3/8&-5H深20的螺纹孔同时进行加工，不仅保证了孔的加工精度，而且还大大地提高了加工效率。

The modular machine tool is used to tap 18 screw holes of M8 and M10 on the left, 15 screw holes of M8, M10, M12 on the right and three screw holes of Z1/4%26rdquo;, a screw holes of G3/8 on the back surface. The modular machine tool uses the horizontal-type single location three-side processing plan, the processing and assembly technology capability is good, and it clamps conveniently.

同时采用机械滑台，一次装夹，对左面15个M8-7H深14和3个M10-7H深15的螺纹孔，右面7个M8-7H深14，3个M10-7H深15，5个M12-7H深20的螺纹孔以及后面3个Z1/4%26quot；-5H深20和1个G3/8%26quot；-5H深20的螺纹孔同时进行加工，不仅保证了孔的加工精度，而且还大大地提高了加工效率。

Insert special bolt into the preset hole of C form parts ,where the bolt will be fixed into the threaded hole of wedge ,then screw the bolt on with a socket spanner until the first nut drops .

将专用螺栓插入C形无件预留孔与楔块的螺纹孔相连，用套筒扳手拧紧螺栓直到第一个螺帽自行断落。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失