螺母

The relief valve pressure of multi-valve has been adjusted after tested, you can not lesscrowd or adjust the safety nut.

多路阀出厂后，安全阀压力已调定，不得任意松动或调整安全螺母。

Long nut posts and rotary locking short rods are adopted in TGP ship lift safety mechanism.

三峡升船机安全锁定机构采用长螺母柱、旋转锁定短螺杆系统。

GRP anchor rod is made mainly of rough-surfaced or threaded rod which were intertwined by fiberglass and enganced resin, consists together with pallet and nut,etc.

玻璃钢锚杆是采用玻璃纤维，增强树脂经拉挤缠绕复合而成型的表面粗糙式或全螺纹杆体，配以托盘，螺母等构件组成的锚杆。

Especially the stainless steel rivet nuts, we take the lead in using cold forged technique, not only save materials,good looking but also loading force, shearing force and torque force all reach international standard.

就不锈钢铆螺母而言，我们已率先采用冷墩一次成型技术，不仅节约材料，外观精美，而且载荷力，剪切力，以及扭力均达到国际标准。

About the stainless steel blind rivet nuts we use cold forged technique, not only save materials but also definition better than turning ,tension force, shearing force or torque force all reaches international standard.

就不锈钢铆螺母而言，我们已率先采用冷墩一次成型技术，它的优点是外观精美，光洁度高，棱角成型到位，，而且拉力，剪切力，以及扭力均达到国际标准。

Rivet, blind rivet, structural rivet, alu. rivet, monobolt, stainless steel rivet, steel rivet, pneumatic riveting tool, avibulb, avinox, stavex.

8D16 8D18 铆钉，抽芯铆钉，气动铆钉枪，气动铆螺母栓，结构型铆钉，铝铆钉，拉丝铆钉，杯型铆钉，不锈钢铆钉，铁/不锈钢单鼓铆钉，铁双鼓铆钉，不锈钢双鼓铆钉。

Our main products are high speed hole rivet series, compound bolt series, mobile bolt nut series, self attack and machine bolt series, nonstandard abnormal shape bolt series, fasten accessory products series, fasten accessory tool series, etc.

主要产品有快速空心铆钉系列、组合件螺钉系列、手机螺钉螺母系列、自攻和机器螺钉系列、非标异型件螺钉系列、紧固件配套产品系列、紧固件配套工具系列等。

2 The provisions of valve flap stent thrust nut in space; 4.3 will bring more than ejector stem components, and into the valve flap bracket, now can adjust screw ring on the injector; adjustment ring discharge pipe may be twisted too high in case of this case, when the valve assembly after the valve flap in contact with its seat before the valve flap seat will have an additional load on the adjustment ring edge, in order to avoid this from happening, should enable the adjustment ring hole just below the injector thread, through which holes should not be able to see thread.

4.2 规定阀瓣支架与止推螺母中的间隙； 4.3 将喷射器提起超过阀杆组件，并放到阀瓣支架上，现在可以把调节环拧在喷射器上；调节环可能在排放管上拧得太高，如遇此情况，当阀门组装后，在阀瓣与其座相接触前，阀瓣座将加载荷于调节环的边上，为了避免此情况的发生，应使调节环上的孔正好低于喷射器的螺纹，通过这些孔应不能看到螺纹。

3 Open the regulator and the nozzle ring ring screw fixation screws; 1.3.4 release and remove the valve cover nut; 1.3.5 screw bolts with rings at the stem, from the valve assembly of the upper part of the body perpendicular to bring devices; when the upper part of unit from the valve body will be raised when the stem or any part not allowed to have any sway movements, any shaking could damage to the valve seat.

1.3.3 拆开调节环固定螺丝和喷咀环固定螺丝； 1.3.4 松开并拆下阀盖螺母； 1.3.5 用吊环螺栓拧在阀杆上，从阀体内垂直提起组装的上部装置；当从阀体内将上部装置提出来时，不允许阀杆或任何部件有任何的摇摆动作，任何摇动都可能损坏阀座。

12patients were given fracture reduction,then penetrated 2 pieces of 3.5mm bony circular needle through fracture sections,tighten the jion-arm nut,the fracture sections will get in touch each other closely,then close the wound.Functional exercises would be given after 3 weeks.When X plain showed us the fracture reach or almost reach clinic heal,remove the external fixator which was substituted by using the small splint for protection untill fracture heal completely.

方法12例患者经整复骨折后，在骨折断端各贯穿2枚3.5mm骨圆针，旋紧连接杆螺母使骨折面紧密接触，然后根据伤口具体情况关闭伤口。3周后功能锻炼。X线复查证实骨折达到或接近临床愈合时拆除外固定器，改用小夹板保护至骨折完全愈合。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷