螺母

Internal soft sealing gate valve block is embedded copper nuts valve board hanging on the rubber lining side, similar to the gate of the structure, due to the activities of the friction nut block valve plate of rubber lining is easy to peel.

国内软密封闸阀的铜螺母块是嵌挂在衬胶阀板上方的，类似闸阀的结构，由于螺母块的活动摩擦容易使阀板的衬胶剥离。

This paper takes the cylindrical boult of the 40 flour mills as the object of study,establishes the corresponding mechanics model ,connects theory to reality,designs the nut conicity,then uses the same conicity offsetting poor alignment between the nut and the cylindrical boult,decomposes reinforcingsteel radia.

以40型面粉机圆筒筛为研究对象，建立相应的力学模型，通过理论结合实际，设计螺母锥度，在螺母与圆筒筛之间采用同锥度错位配合，将钢筋的径向受力通过锥面分解到钢筋轴向一部分，使得钢筋在轴向和径向都保持尽可能小地受力。

A spokesman for Buckinghamshire said there were 1,800 NUT members in their schools but had no idea how many would strike: We are desperately hoping headteachers will tell us whether they are closing early week but the NUT representative only has to give 24 hours' notice.

发言人白金汉郡说，有1800螺母的成员在他们就读的学校，但不知道有多少会罢工的：我们正在急切希望校长会告诉我们，无论是早期的闭幕周，但螺母代表不仅要给予24小时通知。

4 Check the bolts, nuts Check bolts, nut thread.

2.4 检查螺栓、螺母检查螺栓、螺母的螺纹。

Make sure check the bolt and nut before testing run. and if they become less crowded, fastening again.

试车前务必检查所有螺栓、螺母是否有松动，若有松动的螺栓、螺母必须重新紧固。

BALL NUT, A fixed spherical nut driven by the jackscrew for flap and stabilizer movement.

球形螺母，用以使襟翼和水平由粗重螺杆驱动的固定的球形螺母，安定面运动。

Place wrench (08-A10 5) on travel stop nut, rot ate wrench counterclockwise unt il travel stop nutdisengages upper rod.

把限位螺母扳手(08-A105)套在限位螺母上，逆时针旋转扳手，直到限位螺母脱离上阀杆。

Main Products: stainless steel hose, hexagon screws, hexagon nuts, cylinder Xiao, round nut, flat keys, set screws tight, 65-Meng, Qing-lin copper, hole, shaft ring, bearings tight set screw back unloading sets Edible Oil Bottle glib, stainless steel hose clamps, Yingde nut ring system of the United States and Japan.

主要产品：不锈钢喉、六角螺丝、六角螺母、圆柱肖、圆螺母、平键、紧定螺丝、65猛、麟清铜、孔、轴挡圈、轴承紧定螺丝、退卸套、油瓶油嘴、不锈钢喉箍、英德美日制螺母挡圈。

Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。

B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷