螺旋面

2At drive than will certainly,driven gear, while having the more same sizes, hyperboloid have diameter not larger of gear wheel not initiative than corresponding spiral awl gear wheel, intensity and bigger initiative gear wheel axle and bearing rigidity of higher teeth of a cogwheel.

螺旋角是指在锥齿轮节锥表面展开图上的齿线任意一点A的切线TT与该点和节锥顶点连线之间的夹角。在齿面宽中点处的螺旋角称为中点螺旋角(图5—4)。通常不特殊说明，则螺旋角系指中点螺旋角。双曲面齿轮传动比为

We build the model for the enveloping worm helix parametric equation and then analyze its relations with the enveloping worm helix tooth surface equation,thus establishing the characteristic model of the involute helicoid enveloping worm′s generative gears.

渐开面环面蜗杆的三维构建属复杂曲面造型，文章在环面蜗杆螺旋线参数方程建模的基础上，分析讨论了其与渐开面环面蜗杆螺旋齿面方程的对应关系，建立了渐开面包络环面蜗杆产型齿的特征模型。

Considering the effect of load and helical angle on the instaneous width of contact area, this paper uses the BEM program for calculating the deformations at different place along the width of convex tooth and concave tooth of W-N gear and gets the relevant deformation curves.

并首次应用三维边界元方法，在计入齿面瞬时接触迹宽度随外载、螺旋角而变化的条件下，计算了双圆弧齿轮凸齿面端部和凹齿面端部的变形。

The formation of tooth face is analyzed based on the theory of original curve and area as well as the logarithmic spiral polar coordinates equation.

提出了一种新型锥齿轮-对数螺旋线齿锥齿轮传动形式，并以基曲线和基曲面滚动原理为基础，结合对数螺旋线极坐标方程，分析了对数螺旋线以及对数螺旋线齿锥齿轮齿面的形成过程，建立其了齿面方程。

This study refers to the conditions of practical powder metallurgy manufacture process, and proceeds to experiments and gear precision measurements as well as investigation on the effects of two parameters, powders and pitch circle radius, on gear precision. The relationship between gear parameters and gear surface deviations was derived from the mathematical model for the involute helical gears and the analysis of gear surface deviations.

本论文将采用实际上粉末冶金螺旋齿轮的制程条件，进行试作实验与齿轮精度的量测，以探讨粉末及螺旋齿轮之节圆半径这两个制程参数对於齿轮精度的影响；同时应用齿轮创成原理所推导之螺旋齿轮数学模式，配合齿面变异分析，求得齿轮设计参数改变量与齿面变异量之关系。

Besides, the relationships among the tooth numbers and the helical angles of the helical type shaving cutter, the tooth surface deviations and tooth contact conditions are also investigated.

同时，本论文也根据齿面接触分析之结果探讨创成Helipoid齿轮的螺旋型刮刨刀之齿数、螺旋角与齿面差异以及齿面接触情形间的关系。

There are three forms of symmetry in virus capsids: icosahedral , helical and complex forms.

壳粒排列的方式使病毒的结构呈几何对称，病毒衣壳有三种对称形式：二十面体立体对称、螺旋对称、复合对称，螺旋结构呈杆状，而二十面体由对称的亚单位组成近似的球状，非对称的衣壳是较复杂的形式，往往与细菌病毒有关。

The main products are: R Series Hardened helical gear reducer, S series helical gears - worm reducer, K Series helical gears - spiral bevel gear reducer, F series parallel shaft helical gear reducer, T series of spiral bevel gear to me , RV series aluminum alloy Worm Gear reducer, MB series of mechanical friction planetary CVT, hardened cylinder gear reducer and specifications of the various types of special gear, the worm reducer the design and manufacture.

R系列硬齿面斜齿轮减速机、S系列斜齿轮-蜗轮减速机、K系列斜齿轮-螺旋伞齿轮减速机、F系列平行轴斜齿轮减速机、T系列螺旋锥齿轮转向箱、RV系列铝合金蜗轮蜗杆减速机、MB系列行星摩擦式机械无级变速器、硬齿面圆柱齿轮减速机及各类特殊规格的齿轮、蜗轮减速机的设计制造。

Through the analysis of the formation principle of helical curves , the uniform equation of taper surface helical curves is established and the optimization analysis is made of the screw wing cutting edge of the taper spiral auger s tip .

通过分析螺旋线的形成原理，建立了锥形面螺旋线的统一方程，并对圆锥螺旋钻尖的翼片刀刃部分进行了优化分析。

Does spiral movement synchronously,a nonlinear model was established by neural networks to describe the relationship between the helical groove and the milling cutter'sprofile,and according to the helical groove axial cross section to simulate the milling cutter's profile.

加工螺旋槽时，针对铣刀刃形的设计，应用包络面原理，采用神经网络方法建立了工件螺旋槽形与铣刀刃形之间的非线性关系模型，并通过工件螺旋槽端面截形模拟仿真出铣刀回转面刃形。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失