螺旋角

Because of the special structure of conical bearings and existence of spiral groove, conformal mapping and oblique coordinate transformation have been processed for calculated regions of the governing equations.

由于圆锥轴承的特殊结构以及螺旋角的存在，对轴承°的求解域进行了保角变换和料坐标变换。

According to the geometrical principle of conical milling cutter with equal helix angle, a new process of rough machining of conical milling cutter with equal helix angle on universal milling machine by using additive equipment is presented.

根据等螺旋锥铣刀几何原理，提出一种借助附加装置在万能铣床上进行等螺旋角锥铣刀粗加工工艺，介绍了该方法加工锥铣刀时工作铣刀的运动方程；给出了附加装置的设计原理，通过对用此方法加工出的铣刀参数进行测试，证明了这种方法的可行性和实用性。

The horizontal universal milling machine technological transformation based on Mitsubishi PLC;2. Analysis of some important points for makinghelical gear on universal milling machine ;3. According to the geometrical principle of conical milling cutter with equal helix angle, a new process of rough machining of conical milling cutter with equal helix angle on universal milling machine by using additive equipment is presented.

根据等螺旋锥铣刀几何原理，提出一种借助附加装置在万能铣床上进行等螺旋角锥铣刀粗加工工艺，介绍了该方法加工锥铣刀时工作铣刀的运动方程；给出了附加装置的设计原理，通过对用此方法加工出的铣刀参数进行测试，证明了这种方法的可行性和实用性。

Besides, the relationships among the tooth numbers and the helical angles of the helical type shaving cutter, the tooth surface deviations and tooth contact conditions are also investigated.

同时，本论文也根据齿面接触分析之结果探讨创成Helipoid齿轮的螺旋型刮刨刀之齿数、螺旋角与齿面差异以及齿面接触情形间的关系。

A new cylinder type forage cutter with high operation was designed and manufactured. Construction design and its performance parameters, helical angle of moving knife, setting height of fixed knife, overload protective device, throwing device and edge shape of fixed knife were analyzed. The results of test were as follows: optimal helical angle of moving knife was 20°, optimal setting height of the center of the cylinder above fixed knife was 20 mm, line speed of blower vane was 13.6m/s ,power consump...

通过对 93ZT - 5 0 0型滚筒式铡草机的设计研究，分析了滑切角、定刀配置高度、定刀刃角对铡草机性能的影响，并对机构设计进行了探讨，试验结果为：动刀的螺旋角为 2 0°；滚筒中心高于定刀 2 0mm ；抛送风机叶片线速度 13.6m/s ；开刃定刀比矩形定刀的功率消耗低 17.5 %；安全防护装置采用牙嵌式安全离合器；研究结果对滚筒式铡草机的设计和应用具有一定的参考价值

Based on the equations, a new method for the geometrical design of hypoid gears is presented.

在这组方程的基础上，提出了一种几何设计的新方法，以大轮的节锥角和节圆半径以及小轮的螺旋角这三个参数为自由变量，以准双曲面齿轮副的偏置角为中间变量，用数值求解方法能够非常方便可靠地确定节锥的参数。

6Hyperboloid initiative gear wheel axle assign above driven gear centre, easy to realize many axle transaxle well versed in, increase the height of unsticking of the drive shaft.

3双曲面齿轮传动的主动齿轮直径及螺旋角都较大，所以相啮合轮齿的当量曲率半径较相应的螺旋锥齿轮为大，其结果使齿面的接触强度提高。

Results show that the milling tool with rake angle 5°, clearance angle: 10°, helix angle: 45° and corner radius: 1 mm is tested on the surface integrity experiment.

实验结果表明，前角5°，后角10°，刀尖圆弧半径为1mm，铣刀螺旋角为45°的几何结构铣刀完成了表面完整性试验中。

Through comparing these stability lobes, it can be find that the milling stability is increased with the increment of helix angle and normal rake angle.

通过对不同参数下稳定性图的研究，发现随着螺旋角和法向前角的增加，铣削的稳定性逐渐增加。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失