螺旋形的

There is usually an extensive network of collaterals and these have a "corkscrew" or "root like oppearance".

通常有广泛网络的抵押品，这些具有"螺旋形"或"喜欢oppearance根"。

The passage and chamber stones are also richly engraved with spiral, lozenge and zigzag motifs.

走廊和内厅的石头上也被刻上了丰富的螺旋形、菱形和锯齿形的图案。

Bractlets developed, herbaceous or succulent, navicular or similar to leaves, surrounding perianth (in Sympegma bractlets absent, but flowers fascicled at apex of branchlets); stigmas papillose only adaxially; embryo conic-spiral rarely planospiral

小苞片发展， herbacfous或肉质的，具小乳突的柱头只正面；很少的胚圆锥形螺旋形平面螺旋状 4

Perianth usually with 1 petaloid whorl (in Saruma with 2 whorls: outer one sepaloid, inner one petaloid), mostly connate into distinct tube, cylindric to campanulate or subglobose; limb rotate, urceolate, cylindric, or ligulate, 1-3-lobed; lobes valvate.

花被通常形成管状一轮(在马蹄香属里有花被2轮：外部一个萼片状，内部一个花瓣状)，大部分合生成显著的管，圆筒状钟形的或近球形；花被管螺旋状，瓶形，圆筒状，或者舌状，1-3 分裂；裂片镊合状排列。

Leaves 10-20, red, spirally arranged, imbricate, scaly, longitudinally striate when dry; basal leaves on scape broadly ovate, ca. 1 cm; middle leaves oblong, ca. 2 cm; apical leaves subspatulate, 3-3.5 cm, subtending inflorescence.

叶10-20，红色，螺旋状排列，覆瓦状，有鳞，纵向干燥时具条纹；花葶上的基生叶宽卵形，约1厘米；中间叶长圆形，约2厘米；顶端叶近匙形的，3-3.5厘米，着生花序。

The models of cutting edge, the flute of ball end milling cutters with spiral flute of different section, and the section profile and relative feed speed of grinding wheel are provided.

分析了三种不同定义的螺旋刃口曲线的异同和与优劣，给出了二轴联动数控加工时不同截形的螺旋沟槽球头铣刀的刃口、沟槽及砂轮截形、相对进给速度等设计模型，并通过实得沟槽及计算机模拟结果进行了验证，认为借助该模型可获得较理想的球头回转铣刀。

Started by massaging the back of the hand fingertips start to finger roots, action should be calm and gentle; and then spiral massage the palm, and knuckles touch points on the palm of the hand; and finally with the index finger and middle finger grip fingers, fingers from the roots to the spiral spin stretching, massage to the fingers of each root.

先从手背指尖开始按摩到手指根部，动作要从容而柔和；然后螺旋形按摩手掌，并用指关节轻按手心上的穴位；最后用食指和中指夹住手指，从根部向指尖螺旋状旋转拉伸，每一根手指都按摩到。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

According to the principles of tooth meshing and manufacturing helicoi ds, a mathematics model is constructed to reflect the manufacture process of nut , and the formula of the grinding wheel section is developed. The parameters of the section are obtained through numeral arithmetic; moreover the parameters of the dresser are worked out. Based on these work, the solid model of the ball scr ew nut, grinding wheel and tooth dresser are developed in the Pro/E software, wh at's more, the process of the dressing...

根据螺旋面加工原理、齿形啮合原理及回转面砂轮加工螺母工艺建立了相应的数学模型，并推导出砂轮截形的计算公式；采用数值计算方法求解砂轮截形参数，进一步得到修整器靠模板的参数；在此基础上，利用Pro/E软件对大导程滚珠丝杠螺母、砂轮和砂轮修整器进行了实体建模，并对砂轮的修整过程和螺母的加工过程进行了运动仿真，有效地验证了砂轮截形的计算结果。

Nowadays in virtue of the developed CFD simulation analysis software—— STAR-CD ,The flow field of the pure water in the half-spirality suction chamber is simulated.

借助于现在发达的CFD模拟分析软件——— STAR-CD 对半螺旋泵吸入室做了纯水的三维模拟分析之后，又在不同含气率的情况下，对半螺旋形吸入室的流场进行了三维模拟分析。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐