薄膜层

The third approach is about the concept of an ITO direct Ohmic contact structure on GaP window layer. The direct Ohmic contact structure is performed by the deposition of an AuBe diffused thin layer and the following activation process on the surface of a Mg-doped GaP window layer. The presence of this thin AuBe diffused layer yields the Be dominant metallic surface layer and significantly reduces the barrier height between the ITO and p-GaP layer. Via the modification of contact structure, not only the brightness was significantly increased but the reliability was comparable to the conventional LED without this structure.

第三个研究为一种具有直接欧姆接触在p型磷化镓窗层与氧化铟锡界面的制程方法，於本研究中并无习知砷化镓欧姆接触层的存在，我们利用金/金铍金属藉由热退火程序，使其金铍原子在磷化镓窗层表面形成具金属特性之薄膜层，降低磷化镓与氧化铟锡接触产生之接面能障；另外，该元件在氧化铟锡直接欧姆接触於磷化镓窗层下，除亮度具明显提升外，在稍大电流(20毫安培)元件可靠度测试下，亦未有明显衰减情形发生。

According to the research team, the biofilms from Northam mine contained a morphologically diverse assortment of bacteria.

科研小组的研究表明，来自诺瑟姆铂金公司矿井中的薄膜层里包含形态上与众不同的一类细菌。

This project was established based on the first cooperative development of optical in situ real time detecting technique probing the atomic scale layer-by-layer epitaxy growth of oxide film. Over the last three years, we have given full play to the advantages and characteristics of both sides and have finished the assumptions and plans of this subject satisfactorily. 1. In Institute of Physics, we set up advanced oblique-incidence reflectivity difference equipment and wrote one data acquisition procedure that made the simultaneous detection of optical signal and RHEED signal into reality. 2. The first observation of sustained oscillations over hundreds of monolayers in both real and imaginary signals during the epitaxy growth of SrNb0.1Ti0.9O3 on SrTiO3 substrate in LMBE testifies that oblique-incidence is an excellent method to detect and monitor film epitaxy growth real time. 3. For the first time, we verify that oblique-incidence reflectivity difference method can be used to monitor the layer-by-layer growth mode during continuous growth through the correspondence between optical signals to atomic or molecular step edge density on the growth surface. 4. Phenomenological analysis shows that optical signals comprise three parts, the first is proportional to the average thickness of the film and depends on the bulk phase dielectric response; the second is proportional to the coverage of terraces and depends on the dielectric response of atoms or unit cells in the terrace; the third is proportional to the coverage of step edges and depends on the effective dielectric response of atoms or unit cells at step edges. This makes oblique-incident reflectivity difference technique a quantitative macroscopic method to monitor film growth.

中文摘要：本课题是在合作首次发展了氧化物薄膜原子尺度层状外延生长光学原位实时探测方法的基础上立项的，三年来，我们充分发挥双方的优势和特点，圆满完成了课题的设想和计划。1、在物理所建立了一套先进的光反射差法装置，编写了计算机系统的数据采集程序，实现了两路光学信号和RHEED数据的同步采集和显示。2、用激光分子束外延在SrTiO3基底上生长SrNb0.1Ti0.9O3薄膜，首次观测到连续外延几百个原胞层，周期振荡的光反射差实部和虚部信号，证明了光反射差法是一种能原位实时探测与监控薄膜层状外延生长的好方法。3、首次验证了通过对生长表面原子或分子台阶密度的响应，光反射差法可用于原位实时监测在连续生长条件下薄膜的层式生长模式。4、通过唯象理论的研究，证明光反射差信号由三项组成，第一项只与薄膜的平均厚度和宏观光学电介质常数有关；第二项与分子台阶面覆盖度和台阶面上分子层的光学电介质常数有关；第三项与台阶边缘的覆盖度成正比，并和在台阶边缘的分子的有效光学介电常数有关。

The two-ply laminate film was required in both printed and plain form, and.

两层压薄膜层都需要在印刷和普通形式，。

Of course, in the process of finishing varnish can decide mentioned on film such as mechanical, optical performance.

当然，在涂饰光油过程中可以决定所提到上光油薄膜层的机械、光学等性能。

In addition,the mechanism isdiscussed on the prevention of interface diffusion via S-passivation.The FexS-dominateinterface reaction layer,is considered to prevent the reaction of Fe with As further meanwhilestabilizes the interface,therefore inhibits the diffusion from the substrate into Fe overlayer,which is different from the model of Anderson.

并且提出了S钝化阻止界面扩散的内在机制，认为在钝化层基底上形成的界面反应层，阻止了Fe和衬底As的反应并稳定了界面，从而阻止衬底元素向薄膜层的扩散，这与Anderson提出的模型不同。

An ultra-high strength, weldable, low alloy steel with excellent cryogenic temperature toughness in the base plate and in the heat affected zone when welded, having a tensile strength greater than 830 MPa (120 ksi) and a micro-laminate microstructure comprising austenite film layers and fine-grained martensite/lower bainite laths, is prepared by heating a steel slab comprising iron and specified weight percentages of some or all of the additives carbon, manganese, nickel, nitrogen, copper, chromium, molybdenum, silicon, niobium, vanadium, titanium, aluminum, and boron; reducing the slab to form plate in one or more passes in a temperature range in which austenite recrystallizes; finish rolling the plate in one or more passes in a temperature range below the austenite recrystallization temperature and above the Ar3 transformation temperature; quenching the finish rolled plate to a suitable Quench Stop Temperature; stopping the quenching; and either, for a period of time, holding the plate substantially isothermally at the QST or slow-cooling the plate before air cooling, or simply air cooling the plate to ambient temperature.

在基体板以及焊接时的热影响区处的低温韧性优异的超高强度、可焊接、低合金钢具有高于830MPa（120ksi）的抗拉强度，并且具有包含奥氏体薄膜层和细晶粒的马氏体／下贝氏体板条的显微层状组织，所述钢的制备过程为：加热含有铁以及特定重量百分比的添加元素的钢坯，所述添加元素为碳，锰，镍，氮，铜，铬，钼，硅，铌，钒，钛，铝，以及硼中的一些或全部；在奥氏体可发生再结晶的温度范围内，采用一个或多个道次，将所述钢坯轧制成板材；在低于奥氏体再结晶温度但高于Ar 3 转变点的温度下，采用一个或多个道次对所述板材进行终轧；将所述终轧板材淬火至一适当淬火终止温度；停止所述淬火；或者在空冷前在QST点基本等温保持所述板材一段时间，或者对所述板材进行缓慢冷却，或者只是简单地将所述板材空冷至室温。

The flavonoid compounds of stems and foliages of 4 species of Reaumuria L.

采用聚酰胺薄膜层析和在紫外光下高效液相层析分析方法，对国产琵琶柴属 Reaumuria L 。

The layer is thin enough to allow it to be positioned between the plungers on a plunger mat and the keys on a key mat of the mobile station.

一种移动台的薄膜层，其可容易地改变移动台的外观，该层足够薄，允许其位于移动台的柱塞座柱塞和键垫的键之间。

Flexibility of the film layer allows a key press to be transmitted through the film insert to one of the plungers, which in turn compresses a contact on a printed wiring board.

薄膜层的柔软性允许键通过薄膜传动到一个柱塞，柱塞又压到印制线路板上的触点。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。