薄壁的

Properties of nonlinear buckling deformation of round soleplate with slot structure under concentrated load are studied.

运用MSC.Nastran求解器计算了薄壁圆柱壳在轴向压力作用下的临界载荷、屈曲模态及薄底板在集中载荷作用下的非线性屈曲问题。

The research mainly focuses upon the unique deformation mechanism, forming method, quality control and parameter optimization, and the key technologies in Finite Element Analysis for the 3D Non-Axisymmetric thin-walled tube spinning. A CNC spinning equipment for the 3D Non-Axisymmetric thin-walled tube has been designed and manufactured based on the experimental investigation of the forming method.

着重研究变形机理、成形方法、质量控制及优化成形工艺参数，解决三维非轴对称零件旋压成形过程数值模拟关键技术；通过对成形工艺方法的试验研究，研制出能够旋压成形三维非轴对称薄壁空心零件的工艺装备。

Based on the Hamiltons principle and the displacement variation principle, one-dimensional discrete finite element method is developed for vibration analysis of thin-walled members.

对于动力分析部分，概述了Hamilton原理，并由位移变分原理出发推导出考虑剪力滞效应的薄壁杆件振动的一维离散有限元法。

In the paper ,microstructure evolutions, mechanical properties, small pox phenomenon on the surface, and corrosion mechanism of die-cast magnesium alloy AZ91D,have been investigated and discussed in detail by means of metallography, SEM, tensile strength testing and salt spraying test combined with computer-aided flow in die analysis, some important conclusions are got and listed in the following1 Structure of the die-cast magnesium alloy AZ91D is composed of global-like structure, which is fine and homogeneous, and actinomorphous dendritic grains.

本课题针对AZ91D压铸镁合金，通过金相分析、SEM分析、力学性能测试和盐雾实验，并结合计算机辅助模流分析，对薄壁镁合金压铸件3C产品的显微组织演化，力学性能，爆痘现象和腐蚀机理等进行了较为细致的研究和讨论，得到如下重要结论。

The extracerebral CCM group,completely different from the intracerebral one, presented elastic and thick-wall vessel.

脑外组CCM表现为弹性较好的厚壁血管，脑内组为弹性较差的薄壁血管。

Thirdly,vessel cell wall was a multilamellate structure, which CMfs orientation of each wall lamellate was perpendicular to cell axis.

基本薄壁组织细胞的细胞壁为多层结构，无明显的薄厚层变化规律。

The technology and items which are needed to be paid attention to,during the procedure of manufacturing of the laminose shells with large diameter,from material preparing to the machining of the bevel on the edge of the shell,are introduced herein.

主要介绍了薄壁大直径短筒体从下料到坡口加工的完整的制造工序及注意事项。

The technology and items which are needed to be paid attention to,during the procedure of manufacturing of the laminose shell s with large diameter,from material preparing to the machining of the bevel on the edge of the shell ,are introduced herein.

主要介绍了薄壁大直径短筒体从下料到坡口加工的完整的制造工序及注意事项。

These masses showed slight to marked lobulation(15/21), and although some are smoothly bordered, but others exhibited a spiculated margin. Less commonly, they included multilobulated masses, a thin-walled cavity, lobar atelectasis without demonstrable mass.

这些肿块可表现出浅分叶（15/21），尽管其中一些边界光滑，大多边界可呈毛刺状，还包括多室性的肿块，薄壁空洞和没有明确肿块的肺不张。

Results The lesion located at the basal segments of left lower lobe in 9 cases (90%), furthermore, 7(70%) at the posterior basal segments; The remainder 1 case (10%) was found at the posterior basal segment of right lower lobe; The lesion present as multiloculated cyst containing fluid and/or air in 7 cases(70%) without contrast enhancement of cyst wall, 3 cases (30%) presented as irregular mass with moderate enhancement, in which bronchiectasis with mucous impaction, calcification or cyst containing fluid may be seen; MRP, MIP and VR reconstructions showed anomalous branches arising from descending aorta in all 10 patients(100%) with draining into left atrium via pulmonary vein,which was consistent with surgery; Ipsilateral hilar lymphadenopathy was demonstrated in 7 cases (70%).

结果 9例（90％）病灶位于左下叶基底段，其中7例（70％）位于左下叶后基底段，1例（10％）位于右下叶后基底段；7例（70％）病灶表现为含液/气的薄壁多房囊腔，增强后囊壁无明显强化，3例（30％）表现为不规则团块，增强后有中等强化，其内有粘液嵌塞的扩张支气管，也可有钙化或液性区；MPR、MIP及VR等三维重建显示10例（100％）均为降主动脉发出异常分支供血，并通过肺静脉回流入左房，血管显示情况与手术相符；7例（70％）患侧肺门淋巴结有增大。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。