致密的

The fluence and frequency of laser was controlled precisely, which could melt and destroy the adiposis tissue without damage to the adjacent tissues. The histological study of treated adiposis tissues, post-operative reaction and clinical results were observed and studied. Results Local adipose tissues were melted and liquefied effectively by the laser. Compact fibrous tissues of cellulite were broken by the laser into loosen structure. The bleeding was lower than traditional method due to the coagulation of capillary vessels. The advantages of laser lipolysis included less edema, petechia and complications, which produced a rapid recovery and satisfactory results.

但该方法也存在疼痛、血管损伤、出血较多[1]等不足，此法主要是利用机械力插入负压吸引管，通过较强的负压将脂肪组织吸出体外，比较适用于大范围、厚层次和疏松的脂肪吸除，难以应用于小范围局限致密的脂肪组织，如面颈部和手臂部等，这些部位脂肪构成较特殊，包含有大量坚韧的呈网状交织的纤维结缔组织，质地较紧密，普通负压难以吸除，吸脂管插入和抽动阻力较大，如强行反复抽吸对组织创伤明显，因此，有必要寻找一种更加有效的治疗方法。

The results show that the particle size and porosity of cathode pellets are significant factors for three-phase interline during electrolysis process.

结果表明：阴极片的颗粒尺寸与孔隙率是影响有效三相界线的重要因素；孔隙率大和粒度小均有利于电解还原的进行，孔隙率小会导致阴极产物形成致密的金属钽外层，阻碍阴极进一步脱氧；成型压力4 MPa时1 150 ℃烧结2 h制备的阴极片具有合适的孔隙率和粒度，电化学活性良好，电解产物形貌均匀，氧含量低。

The components and surface microstructure of the oxide film is analyzed by X-ray and SEM. Its power insulated is measured. The results show that oxidation film is composed of noncrystal Al_2O_3 and a little of crystal γ-Al_2O_3, it shows i...

结果表明，所获得的氧化膜是由非晶态的Al2O3以及少量晶态-γAl2O3组成，呈致密的网状结构，其电学性能满足基板的要求。

This paper reviews the research of horizontal gene transfer related to catabolic gene in biofilms system, and indicts that the dense community structure in biofilms increases the efficiency in horizontal gene transfer among bacteria.

阐述了生物膜系统中与降解基因有关的水平基因转移的研究进展，表明生物膜中致密的群落结构增加了细菌间水平基因转移的效率。

During solidification,α-Al phase nucleates first in the interstices between the short fibers and grows gradually toward the surface of Al2O3 short fibers. The content of Cu and La element around the surface of Al2O3 short fibers increases, both of them enrich almost in the same region, but the content of Cu element in the interstices of short fiber decreases gradually.

结果表明：Al2O3纤维与基体间润湿良好，生成了致密的界面层；在凝固过程中，α-Al相在短纤维间隙中形核并向纤维表面生长，纤维表面Cu和La元素的浓度增大，纤维间隙中的Cu元素的浓度减小。

The most important reasonwas the melting point of V2O5 only being 690℃, which could be volatilized as liquidstate if the temperature exceed this value and led to disastrous oxidation.

合金的 Cr 含量太低，不足以促成连续致密的 Al2O3膜的形成，故以掺杂作用为主，使合金的抗氧化性能降低。

Compact obturation is an important factor for root canal therapy, focusing on reducing the channel of entering root system through mouth and peripheral apical tissue and blocking excitant which is not completely removed during debriding and repairing root canal.

致密的封填是根管治疗成功的关键之一，其主要目的是为减少经由口腔或根尖周围组织渗透进入根管系统的信道，以及将根管清创、修形过程中无法完全移除的刺激物封闭于根管系统内。

It was found that the stability of the melt was seriously affected by the diameter, the density and the homogeneity of the feed rod. The dense and uniform feed rods with pure phase were prepared by complete mixing and repeated sintering at a suitable temperature.

在适当温度下多次预烧结和反复混料，并通过最后的烧结可获得纯相、均匀和致密的原料棒；原料棒直径一般控制在10 mm以内； 3～5 mm/h的生长速度适合晶体生长；生长结束时缓慢降温和退火处理可抑制YFeO3晶体的开裂。

Adopting ameliorated flat arrow-like opener, the machine can cut off the continuity of soil macropore flow; form a compact fertilizer strip on the base of ridge, which can decrease nitrogen leaching by macropore flow. The machine makes use of single-disk to form ridge on the fertilizer strip.

采用改进后的平底箭铲式施肥开沟器能够阻断土壤中大孔隙流的连续性，在垄底形成一致密的施肥带，减少了氮肥在土壤中随大孔隙流的淋溶迁移。

Below 800℃, oxidation rate of fine-grain carbon/ceramic composite was controlled by reaction of carbon with oxygen.

由于细粒炭／陶复合材料具有致密的微观结构，低的孔隙率以及较高的热导率和机械强度，所以具有较高的抗热震性能。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。