自动计算

A set of automatic testing and fault diagnosis system for a certain control and change component is introduced. The realizing technique of hardware and software for automatic testing is discussed.

介绍了某控制转换装置测试仪的自动测试和故障诊断的设计思想，讨论了测试仪的硬软件设计中如何实现自动测试，以及利用FAN算法来计算故障定位测试向量的故障诊断思想和方法。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

We use multi-source points, compute the initial section with geodesic distance and determine the key point while the section moves front.

本文提出一种从散乱点集上自动抽取骨架的算法，它使用多个起始点，根据测地线距离计算初始截面，此后在截面推进过程中自动判别关节点。

In order to measure the passive network's conduction automatically, a network conduction instrumentation based on FPGA technology was designed and implemented according to the design principle of Virtual Instrument. System adopted FPGA technology building a digital flat-top to imitatively produce the high quality sine signal. Under the control of C8051MCU, measurement, calculation and display of the port network's conduction were automatic implementation. Furthermore, the system has the function of frequency step measurement.

摘 要：为了实现对无源端口网络的导纳进行自动测量，根据虚拟仪器设计思想，设计实现了基于FPGA的网络导纳测量仪，系统以FPGA作为数字平台模拟产生优质的正弦信号，在单片机C8051的控制和处理下，自动实现端口网络导纳值的测量、计算、显示，同时具有频率步进测量功能。

To capture the mantic integrity and the intension of the user query, this paper analyzes the characteristics of Chinese integrated word and presents three methods for its automatic detection by combining the mutual information, the prefix and suffix information of integrity word and the confidence for the integrated word. We further design and realize three prototype systems for Chinese integrated word identification based on the proposed overall confidence, partial-confidence and weighted joint confidence methods respectively.

针对在信息检索中完整词整体表达更有意义、更能体现用户查询目的的问题，结合完整词的成词特点，将互信息和完整词前后缀的计算，与组成完整词的可信度相关联，提出基于可信度的三种中文完整词自动识别方法，分别构成基于全信度、偏信度，以及前两者加权平均的混信度的完整词识别方法，设计及实现了基于可信度的三种完整词自动识别中文分词原型系统。

This paper is focusing on the setup of non-contact automatic measurement for the end face of fiber connector by applying micrography and image processing technology.

介绍了一个基于显微成像和数字图像处理技术的非接触式光纤连接器端面自动检测系统：待测的光纤连接器固定于显微平台上，CCD接收显微物镜放大的图像并输入计算机中，然后由系统软件自动对图像进行对比度增强，二值化，平滑去噪，图像分割等处理，从而分析计算出纤芯、包层的各项几何参数。

Recalculation of results; Statistics of up to 120 samples including result limits check, outlier test.

测量结果的重新计算，并可对多达120个样品测量结果的自动统计，结果范围自动检测，超差剔除

In the computer simulation aspect, following work has been down:At first, the Wolfgang Schreiner's model is employed and extended to a new computer arteriole optimal growing model. Many new algorithms are described, such as signal tracing, resistance calculating, resistance balancing and flow balancing. With these algorithms and methods, the arteriole networks can be grown successfully on microcomputer.Secondly, a growing-network ordering method, which is called auto-centripetal ordering method of the growing networks, can be employed to order the growing networks to calculate the average parameters of the networks in level series.

在计算机模型及仿真方面：首先本文改进、推广了WolfgangSchreiner模型，提出小动脉计算机优化生长模型，以及信号灯追踪、计算网络阻力、阻力平衡和流量平衡新算法，利用这种模型和算法成功地在微机上生长出了小动脉网络；第二，本文提出生长网络自动向心分级法，对生长网络进行了自动分级，并将网络参数的分级统计结果与A。

With the rapid development of the research on computer and various related fields,and the rise of the research and application in the visualization of science computation and multimedia technology, digital image processing changed from a special field subject into a tool of a new science research and human-computer interface.

前言在日常生活中，图像处理已经得到广泛应用。例如，电脑人像艺术，电视中的特殊效果，自动售货机钞票的识别，邮政编码的自动识别和利用指纹、虹膜、面部等特征的身份识别等。早期的计算机无论在计算速度或存储容量方面，难于满足对庞大图像数据进行实时处理的要求。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了