自动的

The machine after the band is inserted in it can automatically finish band-gathering, thermal joining, cutting-off and new band starching and is equipped with an auto-stop drive, fast, high efficiency, time and labor saving and high quality of packager.

在插入包装后，机器能自动完成聚带，热合，切断，并出带的捆扎过程；且有自动停机之功能；其工作速度快，效率高，省时省力，捆扎质量高。

AUTOTHROTTLE, A system which automatically controls the throttles of an airplane.

自动油门，自动控制飞机油门的系统。

This controller operates automatically according to the batch sequence and stops automatically when the totalized flow reaches batch loader set value.

控制器按批程序自动运行，当计算流量的总数达到批设定值时，自动停止。

In the power supply of the windlass mechanism, carriage trolleying mechanism and slewing mechanism,and install master ZK pneumatic switch,and current is 120A,if the current load more 120A,the power will be automatism cut off.

3.5.2.2 自动空气开关 automatism pneumatic switch 在卷扬机构，小车牵引机构和回转机构的供电线路中，装有总空气开关 ZK，脱扣电流为 120A，若线路负载超过 120A，可自动切断电源。

Considering the inconvenience of regulation and difficulty of parameter tunning as AC servo system in practical situation, three ways of intelligent control approach to realize auto-tuning and autorecognization of AC servo system, are proposed, which is a robust controller based on two-degrees-offreedom with no tuning to controller, a auto-tuning controller based on fuzzy reasoning with no inertia recognization but tuning parameter of controller, a strategy recognizing inertia of servo system and tuning parameter or structure of controller automatically. In the same time, these control strategies are analyzed from the theory and reliability. The comparative analysis of three measures on strong and weak points is made by simulation and experiment results.

针对交流伺服系统在实际应用中存在的系统调试不便、参数调整困难等问题，提出了实现交流伺服系统自调整和自识别等智能化控制策略的三条途径：一是具有控制器无调整特点的二自由度鲁棒性控制器；二是惯量无识别但需自动调整控制器参数的模糊推理自调整控制器，三是自动识别伺服系统转动惯量并自动调整控制器参数和结构的方案，从理论分析和可实现性两方面对这些控制方案进行了论述，并通过仿真和实验研究，对比分析了各种方案的优缺点，得到了一些有益的结果。

According to the key technology of offline test of analogy ARINC429 aviation bus ,a novel automation test system based on 8-bit single-chip is designed.

在TDC-1综合信号装置自动测试系统中，针对模拟ARINCA29航空总线进行脱机检测这一关键技术，设计了基于8位单片机的新型自动测试子系统。

The series automatic quantitative packing scale there is the main component parts: the feed body weight bodies, executive bodies pneumatic, folder BAG institutions, dust institutions, such as electric control part of an integrated automatic packaging systems.

该系列自动定量包装秤主要构成部件有：进料机构、称重机构、气动执行机构、夹袋机构、除尘机构、电控部分等组成的一体化自动包装系统。

Article recommend a regard 8031 one-chip computers as core stretch, outer to expand electricity , AT93C46 of chip , wipe , get rid of programmable read-only memory, it more have reveal LED,when, minute or second and not last button ringing bell device automatically at the time of school of sign with indicator lamp.

机电毕业论文：自动打铃器设计说明书共30页，10980字摘要文章介绍了一种以8031单片机为核心片，外接扩展芯片AT93C46电擦除可编程只读存储器，并带有数码LED显示，时、分、秒和以指示灯做标志的按键校时自动打铃器。

According to the quality and efficiency question existed in machining end surface inside and outside of big diameter hole in the big case part, the process of machining with a new auto-feed boring head is proposed.

针对大型箱体类零件上的大直径孔内外端面加工中存在的质量和效率问题，提出了利用自动进给式镗头进行加工的方案，对自动进给式镗头的主要参数进行了详尽的论述，并通过工艺试验，为自动进给式镗头的设计提供了理论和实践依据。

According to the quality and efficiency question existed in machining end surface inside and outside of big diameter hole in the big case part, the process of machining with a new auto feed boring head is proposed. The main parameters of the boring head are discussed in detail. The basis of theory and practice for design of the auto-feed boring head is provided through engineer testing.

针对大型箱体类零件上的大直径孔内外端面加工中存在的质量和效率问题，提出了利用自动进给式镗头进行加工的方案，对自动进给式镗头的主要参数进行了详尽的论述，并通过工艺试验，为自动进给式镗头的设计提供了理论和实践依据。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。