膜层

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Geminis can intercalate into the SAM and form a second layer on the hydrophobic DDT film.

其吸附方式有两种，一种是单个分子插入到膜内，一种是在膜的表面形成第二吸附层。

In the example, in the upper side layer of the pixel electrode 7a, an interelectrode insulating film 8, a common electrode 9a in which slit-like openings 9b are formed, and an alignment layer 16 are sequentially formed.

地，覆盖作为像素开关元件的薄膜晶体管30地形成层间绝缘膜6，并通过该层间绝缘膜6的接触孔6a及漏电极5b，使像素电极7a电连接于薄膜晶体管30的漏区域1d。

The kinetics of the inner layer film growth at open-circuit potential is approximately logarithmic.

在自腐蚀状态下，内层膜的生长近似服从对数规律，外层膜的生长则不服从对数规律。

The membranous material was composed of three layers membranes, and some were associated with the assembly intermediates.

膜样物质由三层膜组成，它的一端和病毒装配中间体相连。

Results The isolating function of nonabsorbent gauze was twice as much as that of absorbent gauze; 15sheet absorbent gauze was enough to protect burnwound and provent the oozing of humor from passing through dressing; the permeability of artificial biological dressing was 3.8 times as much as that of superficial skin graft; on wound, the stickiness of artificial biological dressing was 0.5 times as much as that of absorbent gauze.

结果 在抵抗外界污染方面，非脱脂纱布的抵抗力是脱脂纱布的2倍；在隔离保护烧伤创面方面，15层脱脂纱布已能有效保护创面从而防止渗液外漏；人造皮膜的通透性是刃厚皮片的3.8倍；人造皮膜与创面的黏附力是脱脂纱布的1/2。

The results show that underlayer oxhide, coloring agent and diluent solvent are the important effects of producing transfer-film leather.

研究了移膜革硫化成型效果的影响因素，结果表明，在移膜革生产中，所选用的二层皮、着色剂及稀释溶剂是其主要的影响因素。

Xinle HuaBao Plastic Film Co.,Ltd.imports internationaladvanced production lines,by virtue of new technology and super technique of production ,deals with the exploitation,research and production of various plastic film.S o our company is a professional factory that produces high grade PEBA ventilating film and tri-layer co-extruded PE punching base material film at domestic.

新乐华宝塑料薄膜有限公司，引进具有国际先进水平的生产线，凭借新工艺和高超的生产技术从事塑料薄膜的开发、研制、生产，是当今国内生产高档PEBA透气膜、三层共挤PE打孔基材膜的专业厂家。

The components of pellicle protein from whole saliva were studied by the use of HA chromatography as a model to form experimental pellicle.

采用羟基磷灰石柱层析形成实验性获得性膜的体外模型，研究全唾液获得性膜蛋白的组成成份。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。