脱模

Shun Jia grinding technology main products are: vibration grinding machine, grinding stone, smart rack, polishing agent, slurry, with the exception of the Prince of water, environment-friendly cutting oils, paint remover, degreasing agents, mold release agents, anti-rust oil, oil powder, aluminum acid off, cold off agents, defoamers and so on.

顺佳研磨科技主要产品有：振动研磨机、研磨石、叻架、抛光剂、研磨液、除腊水、环保型切削油、脱漆剂、脱脂剂、脱模剂、防锈油、除油粉、铝酸脱、冷脱剂、消泡剂等。

Then injection machine is chosen, as well as the mold concrete design, including several important parts: the number of the cavity, the dividing face, designing of the injecting system, cooling system, air supplement and platoon overflows system, the outing mechanism, the mechanism for taking out the core and so on.

然后是注射机的选择，接下来是模具的具体设计，其中包括几个重要的部分，如型腔数的确定，分型面的确定，浇注系统，冷却系统，引气排溢系统，脱模机构，抽芯机构等部分的设计。

The last and the most important part is the detail design of injection mould , include formate port design , noting system ,cooling system, air supplement and platoon overflows system, the outing organizations, the organization for taking out the core and so on.

最后对模具的具体结构进行了详细的设计，包括成型零件具体尺寸计算，浇注系统，冷却系统，引气排溢系统，脱模机构，抽芯机构等部分的设计。

Other products are release agents, anti-rust agent, mold wash water, thimble oil, hydraulic oil.

其它产品还有脱模剂、防锈剂、洗模水、顶针油、液压油等。

This design from one mode to a cavity is now a two-chamber because a Modulus carried out when the design of a cavity and found a lot of products a greater impact on the quality of the defect, such as lack of cold Liaocao, melting Stripping of instability and mobility difficulties and other factors.

本设计由原来的一模一腔正改为现在的一模两腔，原因是当进行一模一腔的设计时，发现了很多对制品质量影响较大的缺憾，例如缺少冷料槽，熔体流动不稳定和脱模困难等因素。

In die designing, the use of slide block is very extensive, but using too many slide blocks, it is very difficult for assembling and testing.

通过对限幅绝缘盖板的工艺分析，确定了开放型腔、滑块脱模的模具结构。

And through designing the parting line , running gate system, modeling parts , ejection stripping mechanism , cooling system , choosing adaptive standard mould base and standard parts ,it finished the whole mold design scheme for the Micromotor shell.

并通过对分型面、浇注系统、成型零部件、顶出脱模机构、冷却系统的设计，选用适合的标准模架及标准件，完成对电机外壳的一套完整的模具设计方案。

The lubricants of casting mold used in green sand transfer coating were investigated under impact pressure casting.

在气冲造型条件下对粘土砂转移涂料的脱模剂进行了研究。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。