胶料

On decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin,higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75

但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubbleat next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and causebubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking backand back sucking back It setting sucking back to prevent flow and line.It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is ery important too. Sucking back include front sucking back and back sucking back It setting sucking back to preent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder resere air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

Based on the analysis of the theorem and constitute of emulsin deaerator,this article illustrate that emul- sion deaerator could deaerate the entrained foam in papermaking,increase the retention and sizing efficiency,and improve paper machine runnability.

通过对乳液型脱泡剂的工作机理和组成特点的分析，说明了乳液型脱泡剂应用在造纸生产中可以脱除浆料中的携带泡沫，提高助留效果和纸张的施胶度，并且可以改善纸机的运行性等。

Fter preparing porous thin film by doctor blade, carbon counter electrode was prepared by sintering porous thin film at low-temperature.

bstract 以廉价的炭黑掺杂石墨粉，氯化聚乙酸乙烯醋为胶黏剂制成导电浆料，在柔性基底上用丝网印刷技术制备薄膜，低温热处理后即得碳对电极。

Will blend material as said or narrated above dumping the Yu field homogeneously along the field end line direction starting from one end , will use glue to cling to slick shave even.

将上述混和料沿着球场的端线方向自一端开始均匀倾倒于球场，用胶扒刮平刮匀。

Based: on the analysis of the theorem and constitute of emulsin deaerator, this article illustrate that emulsion deaerator in papermaking could deaerat entrained foam in papermaking and improve the result of retention and sizing, and improve paper machine runnability.

本文通过对乳液型脱泡剂的工作机理和组成特点的分析，说明了乳液型脱泡剂应用在造纸生产中可以脱除浆料中的携带泡沫，提高助留效果和纸张的施胶度，并且可以改善纸机的运行性等。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。