胶度

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

The staves of glue side, an increase of spine of clearance space whether it be binding line, or binding disc bicriterion, brush side adhesive are two copper-wheel excircle side extrusion, bookbinder controlof width on the side is the thickness of the copper round on both sides.

不正胶胶杠沉陷，补充了书脊间隙不时间无论是胶订联动线，还是胶订圆盘单机，刷不正胶都是通功两只铜轮边圆不正不不背的挤压来完不败的，胶订机上不正胶的阔度是两不正铜轮的薄度。

Producted RF and CRF aerogels by process of sol-gel technics, dynamic-exchange, CO2 supercritical drying, and procedural increase in temperature carbonization methods, which have eximious capability and nanometer network structure; Systemic analysis various factors which effect gel course, such as ratio of reactants and the dosage of catalyst, and probed into the better experiments conditions(the concentration of resorcinol and formaldehyde is more than 2% and the value of R/C is between 50 and 300); During gel course , primary investigated the viscosity curve and particle size distribution of sol-solution, and analyzed the reason of catalyst dosage effects particle size of gel, and confirmed that the up-growth of gel follows the theory of " polymerize increase ".The experiment results indicated that ultrasonic with unvarying temperature disposal shortened gel time and optimized quality of gels, and the factors of ultrasonic effect gel reaction velocity were analyzed; Prepared organic aerogels using compounds of resorcin and hydroquinone substitute resorcinol reacts with formaldehyde the first time, and also optimized the proportion of resorcinol and hydroquinone (the proportion of hydroquinone in 10%～40%).

采用溶胶-凝胶工艺结合动态溶剂交换、CO2超临界流体干燥与程序升温碳化方法制备出性能优良、具有纳米网络结构的RF与CRF气凝胶；深入研究了反应物配比催化剂用量等条件对凝胶过程的影响，得到了较佳的RF凝胶制备条件(RF浓度应大于2%，R/C值取50～300)；初步研究了凝胶过程中的粘度、粒径变化情况，分析了催化剂用量影响凝胶中粒子尺度的原因，在实验上印证了凝胶生长遵循"聚增长"的理论；通过引入超声波改进了RF气凝胶的制备工艺，缩短了凝胶反应时间，提高了凝胶品质，并探讨了超声波促进RF凝胶反应作用的原因；首次用对苯二酚与间苯二酚复配制备了混合有机气凝胶，优化出复配比(对苯二酚含量为10%～40%)。2。

Product fault ink UN-uniform UN-uniform ink products were:(1) water and ink, ink and wash painting the rubber roll version of wear, spindle bearing wear, cots epiderm aging decline, ink, etc;(2) series water roll of layer debranning, cylindricity wear, a thin layer of shoulderpieces for intergradle monlchamus, a product of long a portion of the Ribbon, resulting in a roller 跞 movement oscillating anisotropism;(3) support by Edition of water, rollers, the cylinder, swayig stand, wear, resulting in version tiaodong Cot by cause pressure by version is unstable, produce ink imbalance, ink, ink plate, staves, relying on the old version (students'overloaded) version of COTS and pressure;(4) the water roll chemiluminscent set of aging or poor quality water decline caused by transmission;(5) does not have a regular check of the drum-and-ink roller and version by version-and-ink roller and pressures;(6) if the drum gear wear, and gear spacing is the same as the regular ink "" gear.

二、产物墨色不平均障碍产物墨色不平均的来因有：（1）传水、传墨、匀墨和靠版水墨各橡胶辊的圆柱度磨损超不差，拆轴承的轴脚磨损，胶辊不内脏嫩化，传墨本领回升等；（2）串水辊度层脱皮，圆柱度磨损超不差，暗地有薄积墨层，两脚长出局部有积墨带，变不败滚子跞不静串墨不不平衡；（3）撑持靠版水、墨辊的锁脚，摆不静支架，磨损惨重，变不败胶辊靠版时跳不静致使靠版不抬辛不安定，爆发水墨不不平衡，呈现墨色不不平衡、干版、水墨杠、嫩版等本体；（4）水辊绒套嫩化或质度不差变不败传水本领回升；（5）操纵按期校核各水墨辊及版滚筒与靠版水墨辊的不抬辛；（6）若滚筒传不静齿轮磨损超不差，呈现与齿轮间距不异的有次序的&齿轮墨杠&。不一、套印障碍 1。

The results showed that, as for rice flour system, the amylose content, gel consistency and swelling power of rice flour were the main influencing factors to its gelatification characteristi...

试验结果表明：对于米粉体系而言，直链淀粉含量、胶稠度和膨润力是影响其胶凝特性的主要因素， 3个因素的影响程度大小依次为直链淀粉含量、胶稠度、膨润力。

This paper makes detailed discussion on production process of millable polyurethane elastomers, points out that plasticity has close contact with production process of MPU and product quality.

详细论述了混炼型聚氨酯弹性体的加工过程和特性，通过实验指出了生胶可塑度与MPU的加工过程和质量有密切的关系，影响可塑度的因素有生胶中硬链段的含量、聚酯二醇的结构和生胶的分子

It was considered that the control of the PRD fluid performance and the dosage of flow pattern adjusting agent PF-VIS were the key of the technique. The viscosity of PRD spudding fluid increased rapidly with the decrease of shearing rate, it indicated that it had good sand carrying ability. The spudding fluid was good capacity of high temperature stability under the low shearing rate, its viscosity was much higher than that of traditional drilling fluid, it was beneficial for cutting carrying in big deviated wells and preventing the formation of cutting bed.

认为要控制好PRD弱凝胶钻开液的性能，流型调节剂PF-VIS的加量是关键；PRD弱凝胶钻开液的粘度随着剪切速率的降低而急剧上升，显示了其优良的井壁携砂带砂性能；PRD弱凝胶钻开液体系具有较好的高温稳定性；PRD弱凝胶钻开液体系在低剪切速率的高粘度，大大高于传统聚合物钻井液，有利于在大斜度井携带岩屑以及防止岩屑床的形成。

objective to investigate staining methods for two-dimensional gel(2-de)electrophoresis in multidrug resistance of gastric cancer.methods cultured vincristine-resistant human gastric cancer cell line sgc7901/vcr and its parental cell line sgc7901.variant amount protein of those cells were separated by 2-de.gels were stained with silver nitrate or colloidal coomassie brilliant blue,and scanned by image scanner.results well-resolved,reproducible 2-de patterns of sgc7901/vcr and sgc7901 were established.silver staining was better when protein sample amount was low,overloaded protein will interfere resolution of the maps.gels stained with colloidal coomassie brilliant blue had more protein spots numbers and abundance without apparent trails when increased loading protein sample.conclusion two staining methods were influenced largely by the sum of protein samples,properly selection may be helpful for further study with proteomics in multidrug resistance of gastric cancer.

低甲氧基果胶的胶凝机理及防止预凝胶。。。他扎罗汀凝胶与克林霉素凝胶治疗痤疮。。。注射隆乳后经乳晕切口取出聚丙烯酰胺。。。目的分析利用蛋白质组学方法研究胃癌耐药相关蛋白质中双向电泳凝胶的染色显示。方法培养胃癌细胞sgc7901和长春新碱诱导的耐药胃癌细胞sgc7901/vcr，用双向凝胶电泳技术分离总蛋白，银染及胶体考马斯亮蓝染色，image scanner扫描仪扫描凝胶。结果获得了背景清晰、重复性好的双向凝胶电泳图谱，两种染色凝胶相比，硝酸银染色在样品少时显示更佳，过量则影响图像质量，而胶体考马斯亮蓝染色在上样量增加时的凝胶蛋白质点数目及丰度均增加，并无明显拖尾。结论两种显色方法受样品量影响较大，恰当选用有利于通过蛋白质组学研究胃癌耐药机制工作的进一步开展。

So during monitoring the gel forming in mineral field, for Cr3+ and composite ion cross-linked gel made by produced water and Al3+ cross-linked gel made by fresh water, we advice that the index of viscosity or conventional transition pressure is used to proceed valuation.

当聚合物凝胶体系为区域性网状分子构型时，粘度或传统的转变压力是可以替代阻力系数和残余阻力系数的简单、快捷和有效的评价指标；当聚合物凝胶体系为局部性网状分子构型时，粘度或传统的转变压力指标都很难反映聚合物分子构型特征；在矿场对聚合物凝胶体系成胶效果进行监测时，对于污水配制Cr3+和复合离子交联凝胶体系和清水配制Al3+交联凝胶体系，建议采用粘度或传统转变压力指标进行评价；对于污水配制Al3+交联凝胶体系，建议采用阻力系数和残余阻力系数或本课题提出的转变压力指标进行评价。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失