联接头

Install compression coupling in top float chamber tapping.

在浮子腔接头上安装压紧联轴节。

Wind the crosslinked tape onto welded cable cores to certain size when connectingcables, and then use molding model to effect 0.6Mpa air pressure and a temperature of about 160℃ to sulfurate.

接头时用交联带一层层缠绕包覆在焊接好的电缆线芯上达到一定尺寸，再用成型模具加0.6Mpa空气压力、160℃左右高温硫化成型。

The second method: Use plastic extrusion molding machine to directly extrude the cable's crosslinked polythene insulation material into formation, and then press and sulfurate by a high temperature into shape in specially made sulfuration model.

第二种方法是，用挤塑机将电缆交联聚乙烯绝缘料直接挤入成型模中，再在特制硫化模具中加压、高温硫化成型。国外通常称为EMJ接头。

Recovery and sulfuration of crosslinked polythene insulation layer of cable joint.

电缆接头交联聚乙烯绝缘层的恢复和硫化。

Other transmission products 18, Tsubakimoto JAPAN: transmission chain, cable protective cover, slow motor, coupling, Tensioner kits, torque limiter, overrunning clutch, electric putt, buffers; 19, JAPAN Concord produced by: AC electric drum, DC roller; 20, Japan Concord Industry: universal coupling; 21,: The United States aerogenes fetal-type brake clutch, water-cooled oil-cooling brake clutch; 22, Asahi Seiko: pneumatic brakes, pneumatic clutches, fluid couplings, bearings with Block 23, shinko JAPAN: electromagnetic clutches, electromagnetic brakes, vibration equipment; 24, kokura JAPAN : electromagnetic clutches, electromagnetic brakes; 25, Japan Muto motor: a variety of fans, dust collection machines; 26, Showa Japan: Precision rotary joint, steam joints, hydraulic, coolant dedicated joint; 27, Seiko Kobayashi JAPAN: Block Bearing Belt; 28, Taiwan·×: indexing device; 29, Seiko Epson: Precision multi-joint manipulator.

其它传动系列产品18、日本椿本：传动链条，电缆保护套，减速电机，联轴器，涨紧套，扭力限制器，超越离合器，电动推杆，缓冲器；19、日本协和制作所：AC电动滚筒，DC电动滚筒；20、日本协和工业：万向联轴节；21、：美国产气胎式刹车离合器，水冷油冷式刹车离合器； 22、日本旭精工：气动刹车，气动离合器，液力偶合器，带座轴承23、日本神钢：电磁离合器，电磁刹车，振动设备；24、日本小仓：电磁离合器，电磁刹车；25、日本武藤电机：各种风机，集尘机；26、日本昭和：精密旋转接头、蒸汽接头、液压、冷却剂专用接头；27、日本小林精工：带座轴承；28、台湾谭子：分度装置；29、爱普生精工：多关节精密机械手。

As introduced by relative information, for foreign plants have not solved the joints between over-voltage crosslinked polythene cables so far, the second method should ensure that the crosslinked polythene layer of excessive thickness filled during the later pressed heating sulfuration process has nohuge air hole is produced and left if the thickness extruded at one time is overlarge to 15～30mm during the process of plastic extruding XLPE crosslinked polythene to recover insulation.

第二种方法，据有关资料介绍，由于国外厂家还未解决超高压交联聚乙烯电力电缆的中间接头，在绝缘恢复挤塑XLPE交联聚乙烯的工艺过程中，一次挤出的厚度如果过大，达的时候，要保证填充的过大厚度交联聚乙烯层在后期加压加热硫化工艺中，不产生留存有大的气孔。

The structure brief introduction the dense thick liquid pump of one stud of i-1b s series is formed by four parts electromotor , shaft coupling , pump and bases motive force joining in marriage usefulness uses y s series asynchronous electromotor of three-phase the shaft coupling uses the water pump with the paw mould elasticity shaft coupling the pump by the pump shell , become hollow inside axle and universal twists joints and winds axle , stud , bush and axle seal and package places and goes out the material mouth etc and forms , and the section of stud is the oval for round and bush section , and his interior surface is the duplexing spirals faces .

结构简介 i-1b系列单螺杆浓浆泵由电动机、联轴器、泵和底座四个部分组成。配用的动力采用y系列三相异步电动机。联轴器采用水泵用爪型弹性联轴器。泵由泵壳、空心轴、万向绞接头、绕轴、螺杆、衬套、轴封装置和出料口等组成，螺杆的断面为圆形、衬套断面为椭圆形，其内表面为双螺旋面。

Its short points are: the crosslinked tape exists a smallamount of air gap between voluble layers though being sulfurated under pressure and high temperature; the semi-conductive crosslinked tape so made can not avoid pollutive dust; besides, this craft of winding tape molding has strict requirements on the joint preparation conditions, temperature and whether

其缺点是：一层层缠绕包覆的交联带虽然经过加压高温硫化，其层与层之间必然存有少量气体间隙；制备的半硫化交联带无法避免带有污染尘埃；电缆接头&包带模塑法&工艺技术对接头制作环境、温度、气候要求苛刻。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。