联接

Heat nail with electric iron next press connection point, solid and not easy come away.

然后用电烙铁把钉子加热按入联接处，坚固而不易脱开。

Relations in accordance with the machines to install the rack assembly components, rack location placed slightly tight after all the connecting screws, adjust the rack so that the eight rack Thread smoothly cylindrical pin penetration, fastening screw connection .

按照机器的装配关系先安装机架组件，机架位置放好后稍带紧所有的联接螺丝，调整机架使机架上的八个内螺纹圆柱销钉都能顺利穿入，紧固连接螺钉。

The popular fin and tube type of radiator core has the advantage of fewer slodered joints and is therefore a stronger construction.

The 普遍的飞翅和管类型幅射器核心有较少的好处slodered 联接和是因此更强的construction。

The reactance of this coil, which is connected between the neutral , and ground is made in the range 90 to 110 per cent of the value required to neutral ize the capacitance current.

联接在中性点与地之间消弧线圈的电抗值要在抵消90%至110%容性电流所需值的范围内。

Not to weld the tube connector to the valve manifold box, in order to avoid

。建议不要采用联接管与分气箱焊接的工

The double ends of central tube is penetrated into pipe union nut,chuck ring and seal ring in turn, and the central tube is penetrated into ladder-shaped public connection separately,the thrash pipe union nut is heave,is credible tight connection.

将中心管两端依次穿入由壬螺母、压环、密封圈，并将中心管穿入梯形公接头内，分别将两端的密封圈，压环推入梯形公接头内，锤击由壬螺母凸起，即可靠密封联接。

In the course of designing, to the axle of the cutting department, gear wheel of the transmission, parts such as the bearing and integral key etc, have been designed and calculated, the intensity is checked and selected for use.

在设计过程中，对截割部的轴、传动齿轮、轴承和联接用的花键等部件进行了设计计算、强度校核和选用。

In the course of designing, to cutting the axle of the cutting department, gear wheel of the transmission, parts such as the bearing and spline linking using,etc have designed to calculate, the intensity is checked and selected for use.

在设计过程中，对截割部的轴、传动齿轮、轴承和联接用的花键等部件进行了设计计算、强度校核和选用。

In the course of designing, to cutting the axle of the cutting department, gear wheel of the transmission, parts such as the bearing and spline linking using,etc have designed to calculate, the intensity is checked and selected for use.

在设计过程中，对传动部的轴、传动齿轮、轴承和联接用的花键等部件进行了设计计算、强度校核和选用。

In the course of designing, to the axle of the cutting department,gear wheel of the transmission, parts such as the bearing andintegral key etc, have been designed and calculated, the intensityis checked and selected for use.

在设计过程中，对截割部的轴、传动齿轮、轴承和联接用的花键等部件进行了设计计算、强度校核和选用。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。