耦合

The device to be measured can preciser than that in measure system. By analysing the errors in measure system and the result of some fiber devices, it is showed that"white light"interferent system is of high precision in the measurement of coupling rate and coupling points.

对测量系统的误差分析，以及实测器件的测试数据分析表明，宽谱干涉光纤测量系统在测量光纤或光纤器件的偏振状态分布时，无论是在耦合率测试，还是在耦合点位置测试方面，均达到很高精度。

To analyze the intersystem EMC more distinctly, the method based on port data is presented. The coupling relation between ports is analyzed and the corresponding figure is drawn in the method. EMC of the intersystem can be analyzed by coupling-function and the interference data of port, which are obtained from test .calculation or specified standard.

为了更清晰地分析系统内电磁兼容性，提出了基于端口数据的系统级电磁兼容性分析方法，该方法分析系统内各部件端口之间的耦合关系，画出耦合关系图，然后根据端口的干扰数据（测试、计算或标准规定的数据）和传递函数分析系统的电磁兼容性。

In order to know irradiant dynamic process we must have excitation crosssection of electron collision with molecule. Incident electron energy is inintermediate range. At low energy, there are several good methods thatcalculate electron collision with molecule for example Variation, R-matrix.

此时入射电子的能量已经达到中能，在低能范围内的电子与分子散射有许多好的方法如变分法、R-矩阵方法，在高能范围内利用Born近似等方法也能得到满意的结果，在中等能量范围的电子与分子碰撞则没有相应的成熟的方法，使用比较多的是密耦(Closing-Couple)方法，这种方法将相互作用势分为静态势、交换势、极化势，在耦合态的选取上比较自由，可以根据实际的问题及分子的特性选取耦合作用比较强的通道，这样既能保证精度又能减少计算量。

The coupling system including the vibration of vehicles and bridge structure is set up based on the vehicle-bridge coupling element due to pavement's stochastic irregulation, the motion equation is solved by numerical integration method.

通过基于桥面随机不平顺的车桥耦合单元建立包含车辆振动和结构振动的耦合系统，用数值积分法求解动力学方程。

The dye couplings were found in laminaeⅡ/Ⅲ,Ⅳ and V, but mostly in laminae Ⅱ/Ⅲ.

在Ⅱ／Ⅲ、Ⅳ和Ⅴ层内都观察到染色耦合神经元，但以Ⅱ／Ⅲ层内发生染色耦合的比率为最高。

Then a fully coupled hydrodynamic-wave model OHERENS-SWAN accounting for interaction between wave and current is obtained and adopted to simulate longshore current in Rongxi area.

另一方面又将水动力模型COHERENS和第三代波浪模型SWAN耦合，使两模型能够随时互相交换水流、水位以及波浪信息，最终获得波流耦合模型COHERENS-SWAN并将其应用于荣喜近岸区波流共同存在情况下的波流作用模拟研究。

The laminate composites with magnetic and ferroelectric pieces show the high magnetoelectric coupling coefficients at the appropriate coupling model of applied field.

将磁性和铁电材料进行层状复合，选择合适的外场耦合模式，得到了高磁电耦合系数的复合材料。

Firstly analyzed the operation principle of BDFM;then used the method of parameters calculation based on magnetomotive force and magnetic conductance,and calculated the inductance parameters.

针对目前无刷双馈电机两套不同极数定子绕组之间，耦合能力弱而导致该类型电机功率密度低及性能指标差的问题，以结构简单易于制造的普通凸极磁阻转子BDFM为例，研究了转子极数对电机耦合能力的影响。

Numerical method of maro/micro coupling and coupling of calculation of phase diagrams in simulation on microsegregation were discussed in this paper.

论述了在显微偏析数值模拟研究中宏/微观模型的耦合数值方法和显微偏析模型与相图计算耦合的数值方法。

The characteristic of machined surface of high speed machining aluminum alloy 7050-T7451 is researched by micrographic experiments and analysis. The formation mechanics of machined metamorphism layer has been analyzed and studied. The dislocation-energy model in machined metamorphism layer was established and applied to explain the micrographic mechanics work-hardening using the thermo-mechanical coupling deformation theory and dislocation theory. The experimental results show that the interaction of high dislocation density effect on hardening is more remarkable than that of thermal stress in high speed machining.

利用显微观察方法对铝合金7050-T7451高速铣削加工的工件表面断面和不同深度的表层的微观形貌特征进行系统的研究，确定了高速切削加工铝合金7050-T7451的表面变质层深度为30～35μm；应用位错能量研究了高速铣削加工过程的热力耦合对变质层的影响机理，并通过微观形貌观察证明：与普通切削相比，高速铣削表层塑性变形的能量和位错密度更高；建立了位错密度的加工硬化的动力学模型，研究了加工硬化的热-力耦合形成机理；对微观裂纹的形成机理进行了理论分析，证明位错密度高的高速切削过程中较低速加工更容易产生明显的微裂纹，从分子级乃至原子级的水平进一步揭示高速切削加工表面变质层的形成特征。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。