耐蚀的

According to the appraisal of ablate resistant resin,the properties and application of modified phenolic resin s and PAA etc new ablate resistant resin are Introduced.

根据对耐烧蚀树脂基体的评价，介绍了改性酚醛树脂及芳基乙炔等新型耐烧蚀树脂基体的性能及其应用概况，并指出高性能、低成本是今后耐烧蚀树脂基体的发展方向。

The results are listed as following :㏕he best anti-erosion proportion of resin present is 25wt% in the condition of silicon carbide reinforced SMCC, while the alumina reinforced SMCC is 40wt%.(2) The better anti-erosion results was achieved with the ratio of silicone resin to acrylic resin containing hydroxy being 3: 1.㏕he composites coating tends to be more brittle when added in alundum particles. It also means that the maximum erosion peak of alundum reinforced SMCC tends to normal angle.甌he change of erosion rate of SMCC can be divided into two stages with the increment erodent velocity: the slow erosion stage of the beginning and the stable erosion stage.

首次发现：①SiC增强的复合涂料涂层，树脂含量为25wt％时，具有最佳耐冲蚀性能：Al_2O_3增强的复合涂料涂层，树脂含量为40wt％时，具有最佳耐冲蚀性能；②SiC增强的涂料，有机硅树脂与丙烯酸树脂的比例为3：1时的耐冲蚀性能好于1：1的复合涂料涂层；③Al_2O_3增强体使涂层变脆的倾向大于以SiC为增强体的涂层，即SiC增强的复合涂料涂层的最大冲蚀率出现在30°，Al_2O_3增强的复合涂料涂层的最大冲蚀率出现在75°～90°之间；④低速冲蚀磨损机理主要是弹性变形与疲劳；高速冲蚀磨损机理主要是显微切削和显微犁耕。

RESULTS: Stent materials play an important role in reducing inflammatory reaction and restenosis following stent implantation. As a medical material for humans, the features of stent should be meet the requirements of reliable distensibility, mechanical persistence, good flexibility and geometrical stability, possible small diameter, excellent blood compatibility, as well as good corrosion resistance. All of these depended on the mechanical and physical features of materials.

结果：支架材料的选择在减少机体炎症反应的强度和持续时间，减少支架置入后血管内再狭窄的发生起着重要的作用，作为人体医用材料，对支架各方面性能都提出了很高的要求，包括可靠的扩张性和力学持久性、良好的柔韧性和几何稳定性、尽可能小的外径，优异的血液相容性和耐蚀性，而支架上述特性都依赖于材料的力学和物理特性。

As a medical material for humans, the features of stent should be meet the requirements of reliable distensibility, mechanical persistence, good flexibility and geometrical stability, possible small diameter, excellent blood compatibility, as well as good corrosion resistance.

结果：支架材料的选择在减少机体炎症反应的强度和持续时间，减少支架置入后血管内再狭窄的发生起着重要的作用，作为人体医用材料，对支架各方面性能都提出了很高的要求，包括可靠的扩张性和力学持久性、良好的柔韧性和几何稳定性、尽可能小的外径，优异的血液相容性和耐蚀性，而支架上述特性都依赖于材料的力学和物理特性。

The layers can increase obviously the destiny of microstructure, magnetic properties Br, Hcb, m and compressive strength of the NPMC bonded by plastic. The epoxy coating can improve effectively the corrosion resistance of the NPMC and delay the rust of NdFeB particles, especially the pycno-film of the cathodal electrophoresis epoxy resin plays a dominant role in the achievements. The investigation of the temperature stability of the NPMC bonded by plastic, whose NdFeB magnetic particles are NFZ-1 and Nd〓Fe〓B/α-Fe,〓 made in China, shows that their ergo-temperatures vary with their components.

环氧树脂涂层能有效地改善塑料粘结NdFeB永磁复合材料的耐蚀性，延缓锈蚀的发生，特别是致密的阴极电泳环氧树脂涂层对塑料粘结NdFeB永磁复合材料具有更为优异的防腐作用；国产的NdFeB磁粉（NFZ-1和Nd〓Fe〓B/α-Fe、〓）制成的塑料粘结永磁复合材料的温度稳定性的研究表明〓纳米晶合金制成的塑料粘结永磁复合材料使用温度应不超过100℃，NFZ-1制成的塑料粘结永磁复合材料可在120℃以下工作，Nd〓Fe〓B/α-Fe制成的塑料粘结永磁复合材料可在140℃以下工作。

This paper also introduces properties of rayon carbon fabric/phenolic anti-ablation, and the test results of thermal-resistant articles used on three kind of solid motors ,demostrating that rayon carbon fabric/phenolic articles can resist imping ment by combustion gas flow,wit...

因此，对这些部位要求材料具有优异的耐燃气流冲刷性能。常用的耐烧蚀涂料、耐烧蚀弹性体以及高硅氧/酚醛耐烧蚀材料等虽在

Experiments and tests that the subject of study by the surface treatment of aluminum alloy materials is feasible, through this research projects in the successful solution of a combination of aluminum alloy plating, electroplating gold after the aluminum parts of its corrosion resistance, electrical conductivity and Brazing performance has been greatly increased.

实验和测试证明本课题所研究的铝合金材料的表面处理方法是可行的，通过本课题的研究，成功的解决了铝合金电镀结合力问题，经过电镀金后的铝合金零件其耐蚀性，导电性和钎焊性能也大大提高。

The project for passenger cars with engine piston aluminum alloy, alloy components through optimal design, rare earth - Modification of phosphorus salt air and bottom melting slabs, metal-cast aluminum piston at the end of riser feeding process, heat treatment process parameters of choice , Nano-Detroit surface coating materials, such as key technology research and development with a density of small, light weight, thermal conductivity, and coefficient of thermal expansion of small, high temperature and have sufficient strength, wear and corrosion resistance , Aluminum piston size and good stability, its integrated technical indicators have reached the leading domestic level.

项目介绍（简介、技术特点、应用范围、市场前景、效益分析及对投资者要求。500字以内）本项目针对乘用车发动机用铝合金活塞，通过合金成分优化设计、稀土－磷盐复合变质处理与炉底透气砖熔炼技术、铝活塞金属型铸造底冒口补缩工艺、热处理工艺参数的选择、纳米级活塞表面涂层材料等关键技术的研究，开发出具有密度小、质量轻、热传导性好、热膨胀系数小，并具有足够的高温强度、耐磨和耐蚀性能、尺寸稳定性好的铝合金活塞，其综合技术指标达到国内领先水平。

Pure magnesium was treated by A. C. treatment technique in 0.25mol/L NaZSO4+0.1mol/L NAOH solution. The surface morphology was observed by scanning electron microscopy. The contact angle of the treated surface of pure Mg was measured by the First Ten Angstroms instrument and then its surface free energy can be calculated. The effect of alternating current treatment on the corrosion resistance of the pure magnesium was studied through electrochemical methods in 0.05mol/L NACI+0.01mol/L NAOH solution. The experimental results showed that a uniform and perfect oxide film was formed after A.

采用载波处理方法，用0.25mol/L Na2SO4+0.1mol/L NAOH作为载波处理溶液，对纯镁试样进行载波处理，通过正交试验确定载波处理的最佳工艺参数；用扫描电了显微镜观察载波处理后试样的表面形貌；用First Ten Angstroms仪器测量蒸馏水纯镁的接触角并计算出表面能；用电化学方法研究了在0.05 mol/L NACI+0.01mol/L NAOH溶液中载波处理对纯镁耐蚀性能的影响。

The corrosion resistance of Aluminum alloys is improved by anodic oxidation, if the fatigue behaviors are taken into account, the behaviors of Aluminum alloys by sulfuric acid anodizing is better than by chromic acid anodizing.

阳极氧化是提高铝合金耐蚀能力的常用方法，如果从疲劳性能的角度考虑，经硫酸阳极氧化的铝合金腐蚀疲劳性能比铬酸阳极氧化的更好一些。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失