耐磨性

The result shows that the wearing ability of the compound material is superior to that of the basis alloy and with the increase of the amount of carborundum, it is gradually enhanced.

结果表明：复合材料的耐磨性高于基体合金，随碳化硅含量的增加，其耐磨性逐渐增强。

The covering prepared with the invented dust core contains a good deal of amorphous carborundum, the coating formation is even and has high rigidity with HV0.1 of more than 1190, and has good abradability and the relative abradability is 15.8 times than the Q235 steel.

用本发明研制的粉芯丝材制备的涂层含有大量非晶，涂层组织均匀、硬度高，HV 0.1 ＞1190；耐磨性好，其相对耐磨性可达到Q235钢的15.8倍。

It has good abrasion resistance and it's a new experiment for enhancing abrasion resistance of the crusher hammer.

磨损试验证明锤头具有良好的耐磨性，是提高破碎机锤头耐磨性的一种新尝试。

Increasing quenching temperature can improve the impact toughness and wear property, and the optimal impact toughness (40 J/cm^2) and wear performance of the tested steel can be obtaind by quenching at 1100℃ and tempering at 250℃ SEM analysis finds that the main wear mechanism is cutting wear and fillister under the low stress grinding abrasion.

提高淬火温度有利于冲击韧度和耐磨性的提高，经1100℃淬火＋250℃回火热处理，材料可获得最佳的冲击韧度(40J/平方公分)及耐磨性。用SEM分析发现，在该低应力磨料磨损工况下，实验钢的磨损形式主要有显微切削和凿坑。

The improvement of the frictional resistance is mainly due to the effect of carbon on residual austenite and the morphology of carbides, and an appropriate amount of residual austenite is helpful to improve the impact toughness and hardness of matrix; The spherical VC can hinder the initiation and propagation of crack and improve the frictional resistance.

碳含量对耐磨性的影响主要是通过对基体残余奥氏体量和碳化物形态表现出来的，适量的残余奥氏体使基体具有较好的冲击韧度及硬度；形态较为固整的VC颗粒，对裂纹的萌生及扩展起阻碍作用，从而使材料的耐磨性提高。

Finally, by studying on using saw blades with different matrices cutting different stones, a basic compatibility rule about matrices and stones was concluded, say, when cutting a hard, high quartz and high alkalifeldspar content and strong bonded stone, a high impact strength and low wear-resistance matrix should be chosen; otherwise, when cutting a soft, low quartz or no quartz content and weak bonded stone, a high bending strength, low impact strength and high wear-resistance matrix should be chosen.

最后，通过对不同性能结合剂的锯片切割不同石材的切削寿命和磨损状态分析，得出了锯片结合剂性能与岩石性质之间的一般性匹配原则：即对于坚硬的、高石英含量的花岗岩，宜选用高强度、高冲击韧性、低耐磨性和对金刚石具有良好粘结性能的结合剂；对于低硬度、无石英或低石英含量的易切削花岗岩，宜选用高强度、高耐磨性和低冲击韧性的结合剂。

The wearability is best in vanadium 0.2％ test steel, three times than that of high manganese steel.

在本试验条件下含钒0.2％的试验钢耐磨性最好，是普通高锰钢耐磨性的2倍。

The results showed that abrasion resistance of refiner plate made of high chromium cast iron was better than that of the stainless steel material.

通过对热磨机的磨盘材料不锈钢和高铬铸铁的耐磨性对比研究表明，高铬铸铁比不锈钢有更好的耐磨性。

In this paper,the built-up welding rod of the wear-resisting alloy with boronic compound hard phase is studied by author which is a Cr-Mn-B alloy system, the structure of buitt-up welding layer is consist of eutectic of austenite and contain boronic compound hard phase.

该文研究的硼化物硬质相耐磨合金堆焊焊条为Cr－Mn－B合金系，堆焊层组织由奥氏体和含棚化物硬质相的共晶体组成，由于硼化物硬质相的硬度高，故含硼化物硬质相的共晶体在磨损过程中起到耐磨骨架作用，显著地提高了堆焊层的耐磨性。

The progress on nano-filler epoxy coatings was reviewed, the advanced methods of dispersion and evaluation of nano powders in epoxy resin were introduced and the development of nano-fillers applying in heavy-duty and anti-wear epoxy coaling was prospected.

主要综述了纳米粉体在提高环氧树脂涂料的防腐性和耐磨性等方面的研究进展，介绍了纳米粉体分散改性的先进方法和表征手段，对纳米填料应用于重防腐耐磨环氧涂料的发展进行了展望。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。