英语人>网络例句>耐热的 相关的搜索结果
网络例句

耐热的

与 耐热的 相关的网络例句 [注:此内容来源于网络,仅供参考]

The results show that the flow stress decreases with increasing deforming temperature and increases with increasing strain rate. The flow stress of the alloy during hot compression deformation can be described by constitutive equation in hyperbolic sine function with a hot deformation activation energy of 196.27 kJ/mol. Partial recystallization takes place in the alloys deformed at a high temperature or at a low strain rate, and large number of dislocations and subgrains are observed in the alloy. The elongated grains observed in the samples coarsen with increasing temperature and decreasing strain rate. Correspondingly, the subgrain size increases and the dislocation density decreases. The main soften mechanism of the alloy transforms from dynamic recovery to dynamic recrystallization.

结果表明:Al-Cu-Mg-Ag耐热铝合金在热压缩变形中的流变应力随着温度的升高而减小,随着应变速率的增大而增大;该合金的热压缩变形流变应力行为可用双曲正弦形式的本构方程来描述,其变形激活能为196.27kJ/mol;在变形温度较高或应变速率较低的合金中发生部分再结晶,并且在合金组织中存在大量的位错和亚晶;随着温度的升高和应变速率的降低,合金中拉长的晶粒发生粗化,亚晶尺寸增大,位错密度减小,合金的主要软化机制逐步由动态回复转变为动态再结晶。

The fabrication of fibers was attempted. The copolymers, the copolymers containing MOCT and the copolymer films containing MOCT were characterized by using Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, Differential Scanning Calorimetry, Thermogravimetric Analyzer and X-ray Diffraction etc. The conclusions were summarized as following,1. The AN/MMA copolymers were testified that copolymerization of most AN and MMA occurred and the ratio of AN and MMA in copolymer was less than the ratio of monomers. With the increase of the contents of MMA, the viscosity of copolymer solution, molecular weight and decomposition temperature of copolymers increase.

通过傅立叶变换红外光谱、扫描电子显微镜、差示扫描量热分析、热重分析、X-射线衍射分析等测试方法对得到的AN/MMA共聚物、含有正十八烷微胶囊的共聚物以及共聚物膜等进行了测试和分析,得到如下的研究结论: 1、丙烯腈—甲基丙烯酸甲酯之间发生了聚合反应,共聚物的组成比略小于投料比;共聚物的粘度和分子量随着第二单体MMA加入量的增加有增大的趋势;第二单体加入量的增大使得共聚物的分解温度升高,通过热重分析证实当AN/MMA摩尔比为85/15时,共聚物的耐热稳定性较高。

The hygienic and toxinfree Xinli PP-R pipes serial products are green and environmental construction materials, which have been recommended by the four ministries and commissions of the State Department, The products are heatresistant which means that the temperature of the supplied water can reach 95℃ under the specified long-term working hours, They are also corrosion-resistant and antiscale and can prevent any corrosion and rust in pipes, lavers and bathtubs.

&鑫利&PPR给水管系列产品,质量轻,20℃时的密度为0.89—0.91g/cm3,重量仅为钢管的九分之一,紫铜管的十分之一。由于重量轻,可大大减轻工人的施工强度。耐热性能好:瞬间使用水温可达95℃,长期使用时,当工作压力不大于0.6mpa时,水温可达75℃。这可满足一般生活、生产水温的需要,所以建筑给水PPR管一种较理想的热水管材。耐腐蚀性好:对水中的所有离子和建筑物内的化学物质均不起化学作用,不生锈、不会腐蚀。

PP1740 copolymer is a multi phase copolymer,composed of homo-polypropylene,ethylene-propylene rubber,and crystallizable propylene-ethylene copolymer.Homo-polypropylene part offers rigidity and EPR part offers impact strength.The relative ...

研究结果表明,PP1740共聚物由均聚聚丙烯、乙丙橡胶和可结晶的乙丙共聚物组成,具有优良的机械性能;均聚聚丙烯为PP1740共聚物提供刚性,乙丙橡胶可提高PP1740共聚物的抗冲性能;PP1740共聚物的相对分子质量分布呈多分散性,相对分子质量分布较宽;乙丙橡胶的相对分子质量较大,以直径1~2μm球型微粒均匀分布在聚丙烯基体中,有利于提高PP1740共聚物的冲击强度;PP1740共聚物的熔点较高,耐热性好。

Based on the failure analysis of hot roll, this paper optimizedly adjusts alloy system and summarizes the experience of rolling wiresand improves ail processing properties. Then, it analyses the effects on some natural parameters such as alloy transfer coefficient, surfacing layers, welding current and arc voltage etc.. It confirms the fitting ageing technique. Also, it discusses the microscopic structural transformation back and forth ageing and the effects on hardness change of overlaying metal by some alloying elements including C, Cr, V, W, Mo, Ni, Mn, B, Re through OM, SEM and X-ray diffraction analyses. Finally the abrasive resistance, red hardness, thermal fatigue property and anti-high temperature oxidability are investigated in experimentation.

全文在热轧辊失效分析的基础上优化调整合金体系,总结了焊丝轧制的经验,改善各种工艺性能,分析了几个特性参数的影响,确定了适宜的时效工艺,并通过光学显微镜、扫描电镜和X-射线衍射对时效前后的显微组织转变以及部分合金元素如C、Cr、V、W、Mo、Ni、Mn、B、Re对堆焊层硬度变化的影响进行分析,最后通过试验考察了堆焊层金属的耐磨粒磨损性能、红硬性、耐热疲劳性和抗高温氧化性。

Silica and alumina, to an organic silicone rubber, ShoreA 70, to improve the hardness of silicone rubber material and the results indicated that the addition of silica improved the hardness of the material dramatically, but depressed the heat-resistance markedly; the addition of alumina improved the hardness of the material also, but more loading was needed to achieved the hardness as compared with the silica added materials.

研究发现,添加气相法白碳黑能显著提高硅橡胶的硬度,但使硅橡胶的耐热老化性能明显变差;氧化铝也可以用于提高硅橡胶的硬度,但与气相法白碳黑相比,达到相同硬度时的添加量要大的多;比较而言,通过添加氧化铝获得的高硬度硅橡胶具有较好的综合性能,更能满足电化铝烫印版的制作需要。

The experimental results denoted that the finer pearlite along the austenite boundaries in the as-cast Cr30Ni20NRE steel disappeared first under long-term and high-temperature service condition, and that an umber of Cr- richened carbides were formed due to unila-teral carburizing at long-term and high- temperature, consequently causing Ni to concentrate, bulging and calalyzing decomposition of the carburizing gas.

试验结果表明,长期在高温条件下服役,铸态Cr30Ni20NRE耐热钢中沿奥氏体晶界的珠光首先融入奥氏体,长期高温单边渗碳形成大量富铬碳化物,促使镍富集并起泡形成瘤状物,催化含碳气体的分解;表层瘤状物使辐射管表层疏松,表面积扩张,加快了碳向基体的渗入,提供了碳化物持续长大的条件,并引起沿碳化物周边开裂和奥氏体基体严重萎缩;合金元素的重新分布造成主合金元素铬和镍产生两极分化,镍和硅的富集促使石墨化,与侵入的氧形成内部氧化空洞和膨胀疏松,最终导致构件穿孔失效。

The types,structures of substrates and reaction mediums for the enzymatic synthetic polyphenol resin was surveyed and the manufacturing method,product structure and their performances of the polyphonel resin and aldehyde resin were compared.

概述了酶催化合成聚酚树脂用酶的种类、底物的结构、反应介质;比较了该树脂和传统酚醛树脂的生产、结构及性能特点;指出了其不仅具有良好的耐热性能,可作传统酚醛树脂的替代品,而且具有导电、发光等功能,在光电材料方面显示了极强的应用潜力,但降低HRP催化合成聚酚树脂的成本是其实现工业化亟待解决的问题。

Media Help Everyday we are exposed to the steam often divided into two, one, the boiler steam - saturated steam 2, thermal power plants out of steam - superheated steam 1, a relatively stable temperature and pressure saturated steam, temperature lower than 250 ℃, working pressure lower than 1.6Mpa 2, superheated steam temperature and pressure changes of a high base temperature up to 400 ℃, working pressure is lower than 4.0Mpa For the first steam, we usually use soft sealing steam solenoid valve as follows: Structural characteristics This valve is a valve and Balance valves main valve by the two vice components with the second open valve Pilot solenoid valve Heat: electromagnetic part, some with special high temperature seals and sealing materials, electrical materials, and apply a variety of insulation measures Wear: selection and reasonable Globe Valves guidance suite valve cup and clever use of fluid lubrication, reduce wear, increase life expectancy Resistance to condensation: condensation of steam pipeline valve on the steam water is an important factor in action, the valve will not affect the condensation water Other uses - soft sealing steam solenoid valve This series solenoid valve can Safety valves be widely used in textile, printing, chemicals, plastics, rubber, pharmaceutical, food, building materials, machinery, electronics, surface treatment and research sectors and bathroom, dining room, air conditioning automatic control system.

介质说明日常生活中我们接触到的蒸汽常分为两种,1、锅炉蒸汽-饱和蒸汽 2、热电厂出来的蒸汽-过热蒸汽 1、饱和蒸汽温度压力相对稳定,电动阀门执行器温度低于250℃,工作压力低于1.6Mpa 2、过热蒸汽温度压力变化基数较大温度最高可达400℃以上,工作压力则低于4.0Mpa 对于第一种蒸汽,我们通常会选用氧气专用阀、铜阀门软密封的蒸汽电磁阀如下:结构特点本阀是由副阀和主阀两大部件构成的先导式二次开阀的电磁阀耐热:电磁部分、密封件部分用特种耐高温电工材料和密封材料,并应用了各种隔热措施耐磨:选材合理,电站阀门阀杯和导向套间巧妙地利用流体的润滑作用,减少磨损,提高寿命耐冷凝:蒸汽管道的冷凝水是影响蒸汽电磁阀动作的重要因素,本阀则不受冷凝水影响其他用途-软密封蒸汽电磁阀本系列电磁阀还可广泛地应用平衡阀纺织、印刷、化工、塑料、橡胶、制药、食品、建材、机械、电器、表面处理和科研部门以及浴室、食堂、空调等自控系统。

It is considered in this paper that the light and heat oxygen resistance ageings of silicone acrylate resin are better than those of normal acrylic and polyurethane resins, through the theoretic investigations into the reaction mechanisms of the light and heat oxygen ageings of high molecular polymer and contrasting, when exposed to light and under a high temperature, the changes in colour,shape, tensile strength and elongation of Silicone Acrylate Resin DX 8501 to the normal acrylic and polyur...

本文通过对高分子聚合物的光氧老化、热氧老化的反应机理的理论探讨和对DX8501硅丙树脂、普通丙烯酸树脂、普通聚氨酯胶膜在紫外光照射下和高温条件下的颜色、形态、抗张强度、伸长率的变化情况对比,认为硅丙树脂的耐光氧老化和耐热氧老化的性能优于普通的丙烯酸树脂和普通的聚氨酯。表3,参考文献8

第52/53页 首页 < ... 45 46 47 48 49 50 51 52 53 > 尾页
推荐网络例句

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面,更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值,分为几个相等的区间作为横轴,并将各区间内所测定值依所出现的次数累积而成的面积,用柱子排起来的图形,也叫做柱状图。

You rap, you know we are not so good at rapping, huh?

你唱吧,你也知道我们并不那么擅长说唱,对吧?